Pick&Place: Unterschied zwischen den Versionen
Chrysn (Diskussion | Beiträge) (Beitrag zur Pick&Place) |
Ripper (Diskussion | Beiträge) K (→Fiducials: Example picture of fiducial added) |
||
| (18 dazwischenliegende Versionen von 4 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| + | {{Maschinenring}} | ||
{{Head_en}} | {{Head_en}} | ||
| + | {{Machine | ||
| + | |image=Liteplacer.jpg | ||
| + | |owner=Metalab | ||
| + | |status=sort of working, training in progress | ||
| + | |requirestraining={{Yes}} | ||
| + | |requiresauth={{No}} | ||
| + | |cost= | ||
| + | |teachers=[[User:ripper|ripper]], ... | ||
| + | }} | ||
= Pick & Place Machine = | = Pick & Place Machine = | ||
[https://www.youtube.com/watch?v=T_v2VJKNZQ0 Liteplacer Introduction Video] | [https://www.youtube.com/watch?v=T_v2VJKNZQ0 Liteplacer Introduction Video] | ||
| + | |||
| + | Metalab owns a Pick & Place machine which is mounted in the window aisle of the [[Elektroniklabor|electronics room]] in the [[WEL|Whateverlab]]. This machine can be used to place SMT components on PCBs automatically. You can find a lot of information about the machne on the [https://www.liteplacer.com/ projects website].<br> | ||
| + | The machine runs via [http://openpnp.org/ OpenPnP], an Open Source SMT pick and place software. | ||
| + | |||
| + | = PCB requirements = | ||
| + | Not all PCBs are created equal. Some PCBs are more suited to component placement with this machine. The following information should help you to design PCBs suitable for automated placement of components. | ||
| + | === Fiducials === | ||
| + | [[Datei:Round_fiducial_on_pcb.jpg|120px|thumb|left|Fiducial on a PCB]] | ||
| + | Fiducials are alignemt marks on PCBs. The standard for these is a 1mm copper circle surrounded by a 2mm soldermask opening. They are used for alignng your PCB via optical detection. For successfull operation there should be at least '''three''', better '''four''' which are places in the corners of your PCB to get the best accuracy for the placement of components. | ||
| + | |||
| + | === Size === | ||
| + | TBD | ||
| + | |||
| + | = Standard operation procedure = | ||
| + | The machine is best operated by followind these instructions: | ||
| + | * TBD | ||
| + | |||
| + | = Financial = | ||
Metalab will be buying the DIY pick&place machine shown in the video behind the link above for deployment in the [[Elektroniklabor|Electronics Lab]]. Half of the machines price will be covered by donations. If you think that buying the machine is a good idea and/or want to contribute, here's the list to financially support it: | Metalab will be buying the DIY pick&place machine shown in the video behind the link above for deployment in the [[Elektroniklabor|Electronics Lab]]. Half of the machines price will be covered by donations. If you think that buying the machine is a good idea and/or want to contribute, here's the list to financially support it: | ||
| Zeile 14: | Zeile 42: | ||
|- | |- | ||
| [[User:anlumo|anlumo]] | | [[User:anlumo|anlumo]] | ||
| − | | | + | |align=right| € 50 |
| − | | {{ | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:redplanet|redplanet]] | | [[User:redplanet|redplanet]] | ||
| − | | | + | |align=right| € 42 |
| − | | {{Yes}} | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:consti|consti]] | | [[User:consti|consti]] | ||
| − | | | + | |align=right| € 100 |
| − | | {{Yes}} | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:zwax|Zwax]] | | [[User:zwax|Zwax]] | ||
| − | | | + | |align=right| € 50 |
| − | | {{ | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:ripper|ripper]] | | [[User:ripper|ripper]] | ||
| − | | | + | |align=right| € 100 |
| − | | {{ | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:Herbert|Herbert]] | | [[User:Herbert|Herbert]] | ||
| − | | | + | |align=right| € 67 |
| − | | {{ | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:datacop|datacop]] | | [[User:datacop|datacop]] | ||
| − | | | + | |align=right| € 75 |
| − | | {{ | + | |align=center| {{Yes}} |
|- | |- | ||
| [[User:chrysn|chrysn]] | | [[User:chrysn|chrysn]] | ||
| − | | | + | |align=right| € 75 |
| − | | {{Yes}} | + | |align=center| {{Yes}} |
| + | |- | ||
| + | | [[User:Pk|pk]] | ||
| + | |align=right| € 49 | ||
| + | |align=center| {{Yes}} | ||
| + | |- | ||
| + | | [[User:OE1WKL|Willi]] | ||
| + | |align=right| € 50 | ||
| + | |align=center| {{Yes}} | ||
| + | |- | ||
| + | | OE1OMA | ||
| + | |align=right| € 50 | ||
| + | |align=center| {{Yes}} | ||
|- | |- | ||
| ''Your name here'' | | ''Your name here'' | ||
| − | | '' | + | |align=right| ''€ 1.000.000'' |
| − | | {{ | + | |align=center| {{No}} |
|- | |- | ||
| bgcolor="lightgrey"| Total | | bgcolor="lightgrey"| Total | ||
| − | | bgcolor="lightgrey"| | + | | bgcolor="lightgrey" align=right| '''€ 708''' / 700 |
| − | | bgcolor="lightgrey"| | + | | bgcolor="lightgrey" align=right| € 708 / 708 |
|} | |} | ||
Aktuelle Version vom 23. Juli 2020, 20:40 Uhr
3D-Scanner - CNC-Fräse - Laser - Reflow Oven - 3DPrinter (Prusa XL, Prusa Mk3S, Prusa Mini) - Vinylplotter - Schweißinverter -Tischbohrmaschine - Drehbank - Ultraschallreiniger - Nähmaschinen
| Language: | English |
|---|
| Pick&Place | |
| |
| Eigentümer: | Metalab |
| Status: | sort of working, training in progress |
| Erfordert Einschulung: | ✔ |
| Erfordert Authentisierung: | ✘ |
| Hilfsbereite: | ripper, ... |
Pick & Place Machine
Metalab owns a Pick & Place machine which is mounted in the window aisle of the electronics room in the Whateverlab. This machine can be used to place SMT components on PCBs automatically. You can find a lot of information about the machne on the projects website.
The machine runs via OpenPnP, an Open Source SMT pick and place software.
PCB requirements
Not all PCBs are created equal. Some PCBs are more suited to component placement with this machine. The following information should help you to design PCBs suitable for automated placement of components.
Fiducials
Fiducials are alignemt marks on PCBs. The standard for these is a 1mm copper circle surrounded by a 2mm soldermask opening. They are used for alignng your PCB via optical detection. For successfull operation there should be at least three, better four which are places in the corners of your PCB to get the best accuracy for the placement of components.
Size
TBD
Standard operation procedure
The machine is best operated by followind these instructions:
- TBD
Financial
Metalab will be buying the DIY pick&place machine shown in the video behind the link above for deployment in the Electronics Lab. Half of the machines price will be covered by donations. If you think that buying the machine is a good idea and/or want to contribute, here's the list to financially support it:
| Name | Amount | Paid |
|---|---|---|
| anlumo | € 50 | ✔ |
| redplanet | € 42 | ✔ |
| consti | € 100 | ✔ |
| Zwax | € 50 | ✔ |
| ripper | € 100 | ✔ |
| Herbert | € 67 | ✔ |
| datacop | € 75 | ✔ |
| chrysn | € 75 | ✔ |
| pk | € 49 | ✔ |
| Willi | € 50 | ✔ |
| OE1OMA | € 50 | ✔ |
| Your name here | € 1.000.000 | ✘ |
| Total | € 708 / 700 | € 708 / 708 |
