Metalock2.0: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springenPete (Diskussion | Beiträge) |
Pete (Diskussion | Beiträge) |
||
| Zeile 15: | Zeile 15: | ||
== How == | == How == | ||
| − | * Only Software of Door Status is on Github | + | * Only Software of Door Status is on Github. |
Lessons learned: <br> | Lessons learned: <br> | ||
| Zeile 22: | Zeile 22: | ||
Hardware documentation | Hardware documentation | ||
* tbd (how is everything connected) | * tbd (how is everything connected) | ||
| + | * Door Status is wired directly to the door status switch. Voltage divider is between the 2 connectors of the soor status Switch. | ||
| + | From 5V to 3V for the Raspberry Pi GPIO. 22K Ohm + 33K Ohm Resistors. | ||
| − | Software documentation | + | Software documentation <br> |
| + | <b>Metalock2.0</b> | ||
* TBD ;) (yeah right..) (pitfalls, config, buildprocess) | * TBD ;) (yeah right..) (pitfalls, config, buildprocess) | ||
| − | * IP: 10.20.30.77 (local IPv4 of | + | * IP: 10.20.30.20 (local IPv4 of DOCKSTAR) |
| + | |||
| + | <b>Door Status:</b> | ||
| + | * IP: 10.20.30.77 (local IPv4 of Raspberry Pi) | ||
| + | * Software of Doorstatus: https://github.com/Metalab/metadoor | ||
== Reference == | == Reference == | ||
Version vom 13. Juli 2018, 22:29 Uhr
BETA!!! Running in Production since years
Currently BETA TESTING please leave all your experiences, ideas, bugreports, suggestions on the discussion page Diskussion:Metalock running since years quite good!
Metalock2.0
- is a custom built lock system and the successor of Metalock
- it consists of a DOCKSTAR embedded linux system, an EMZY sponsored by EVVA and an Arduino
- An Raspberry Pi for serving the Door Status as a Website
Door Status
Door Status is working again:
Available in the local network over IPv4: http://10.20.30.77
Globally available over IPv6: http://[2a02:61:a2::d8]/
How
- Only Software of Door Status is on Github.
Lessons learned:
The Setup is not documented and quite complex.
Hardware documentation
- tbd (how is everything connected)
- Door Status is wired directly to the door status switch. Voltage divider is between the 2 connectors of the soor status Switch.
From 5V to 3V for the Raspberry Pi GPIO. 22K Ohm + 33K Ohm Resistors.
Software documentation
Metalock2.0
- TBD ;) (yeah right..) (pitfalls, config, buildprocess)
- IP: 10.20.30.20 (local IPv4 of DOCKSTAR)
Door Status:
- IP: 10.20.30.77 (local IPv4 of Raspberry Pi)
- Software of Doorstatus: https://github.com/Metalab/metadoor
Reference
Who
Doorstatus Software & Hardware:
- Brought to you by Nico, Nini, Ripper, Phileas, and many other lovely Metalab people <3
- Resurrected™ by Hetti
Videos
tbd
Photos
tbd
Future
We are planning to replace the whole System in the (near) future with an simpler and better setup. Metalock 3.0 - TBA -
