AVRProgrammers: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
Zeile 113: Zeile 113:
 
Check connection:
 
Check connection:
 
  avrdude -c usbtiny -p atmega168
 
  avrdude -c usbtiny -p atmega168
 +
 +
 +
== Any Arduino Board ==
 +
 +
see [Benutzer:Mihi/Programming-attiny45-mit-arduino]
  
 
= Troubleshooting =
 
= Troubleshooting =

Version vom 15. September 2010, 08:53 Uhr

WTF?

We have a small selection of AVR programmers lying around. This is an attempt to document how to use them.

General information

10-pin ISP header pinout

1 MOSI
2 Vcc
3 N/C
4 TX or GND
5 CS
6 RX or GND
7 SCK
8 GND
9 MISO
10 GND

6-pin ISP header pinoout

Note that some boards have a non-standard pinout for the 6-pin headers.

1 MISO
2 Vcc
3 SCK
4 MOSI
5 CS/RST
6 GND

Programmers

RS-232 programmer (ATtiny2313)

RS-232 (ATTiny2313) programmer

This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end.

Programmer type: avr910
Speed: 115200

NB! This programmer uses non-standard device codes for atmega48/88/168 (0x06, 0x07 and 0x08).
To make it work, edit avrdude.conf:

part
    id              = "m168";
    avr910_devcode =  0x08;

Note: This programmer requires the target to be self-powered.

avrdude command lines

Check connection:

avrdude -P <serialport> -c avr910 -b 115200 -p atmega168

USBasp programmer (stripboard)

USBasp stripboard programmer

This is a USB programmer built on a stripboard. It has a USB-B connector in one end an a 10-pin ISP header in the other end.

Programmer type: usbasp
Speed: default

avrdude command lines

Check connection:

avrdude -c usbasp -p atmega168

Example: Program Arduino NG bootloader:

avrdude -c usbasp -p atmega168 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdf:m -U lfuse:w:0xff:m
avrdude -c usbasp -p atmega168 -U flash:w:ATmegaBOOT_168_ng.hex:i -U lock:w:0x0f:m

Avrprog-metaboard

Metaboard AVRprog programmer

A Metaboard-based programmer.

This programmer behaves exactly like the USBasp stripboard programmer.

In the current incarnation, this programmer is not as stable as the USBasp version. We need to figure this out, e.g. ask Christian for advice. Symptoms are aborted operation during read or write. Usually it helps to try again and to run verify as a separate step.

avrdude: error: wrong reading bytes b8

Note: This programmer has a bootloader on it, so it can be updated over USB. There is a jumper to enable the bootloader. This jumper must be off when using it as a programmer and on when accessing the bootloader.

USBTinyISP

The USBTinyISP from Lady Ada. FIXME: Safe vs. unsafe

Check connection:

avrdude -c usbtiny -p atmega168


Any Arduino Board

see [Benutzer:Mihi/Programming-attiny45-mit-arduino]

Troubleshooting

Sometimes, the following happens: avrdude: erasing chip
avrdude: error: programm enable: target doesn't answer. 1

This has shown to be caused by wrong crystal fuse settings, typically an issue when programming fresh chips. To fix, program all fuses first, before erasing the chip.