AVRProgrammers: Unterschied zwischen den Versionen

aus Metalab, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Wechseln zu: Navigation, Suche
(RS-232 programmer (ATtiny2313))
(RS-232 programmer (ATtiny2313))
Zeile 56: Zeile 56:
 
== RS-232 programmer (ATtiny2313) ==
 
== RS-232 programmer (ATtiny2313) ==
  
[[Bild:avrprog-rs232.jpg|thumb|right|200px|RS-232 (ATTiny2313) programmer]]
+
[[Bild:avrprog-rs232.jpg|thumb|200px|RS-232 (ATTiny2313) programmer]]
  
 
This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end.
 
This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end.

Version vom 25. Januar 2009, 13:18 Uhr

WTF?

We have a small selection of AVR programmers lying around. This is an attempt to document how to use them.

General information

10-pin ISP header pinout

1 MOSI
2 Vcc
3 N/C
4 TX or GND
5 CS
6 RX or GND
7 SCK
8 GND
9 MISO
10 GND

6-pin ISP header pinoout

Note that some boards have a non-standard pinout for the 6-pin headers.

1 MISO
2 Vcc
3 SCK
4 MOSI
5 CS/RST
6 GND

Programmers

FIXME: Pictures taken - need to upload

RS-232 programmer (ATtiny2313)

RS-232 (ATTiny2313) programmer

This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end.

Programmer type: avr910
Speed: 115200

NB! This programmer uses non-standard device codes for atmega48/88/168 (0x06, 0x07 and 0x08).
To make it work, edit avrdude.conf:

part
    id              = "m168";
    avr910_devcode =  0x08;

Note: This programmer requires the target to be self-powered.

avrdude command lines

Check connection:

avrdude -P <serialport> -c avr910 -b 115200 -p atmega168

USBasp programmer (stripboard)

This is a USB programmer built on a stripboard. It has a USB-B connector in one end an a 10-pin ISP header in the other end.

Programmer type: usbasp
Speed: default

avrdude command lines

Check connection:

avrdude -c usbasp -p atmega168

Example: Program Arduino NG bootloader:

avrdude -c usbasp -p atmega168 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdf:m -U lfuse:w:0xff:m
avrdude -c usbasp -p atmega168 -U flash:w:ATmegaBOOT_168_ng.hex:i -U lock:w:0x0f:m

AVRProg-metaboard

A Metaboard-based programmer.

This programmer behaves exactly like the USBasp stripboard programmer.

In the current incarnation, this programmer is not as stable as the USBasp version. We need to figure this out, e.g. ask Christian for advice. Symptoms are aborted operation during read or write. Usually it helps to try again and to run verify as a separate step.

avrdude: error: wrong reading bytes b8

Note: This programmer has a bootloader on it, so it can be updated over USB. There is a jumper to enable the bootloader. This jumper must be off when using it as a programmer and on when accessing the bootloader.