Bandsaw: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springenReox (Diskussion | Beiträge) (Die Seite wurde neu angelegt: „The Metalab currently has 3 different Bandsaws. A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. ==…“) |
Reox (Diskussion | Beiträge) (remove old saw) |
||
| (17 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| − | The | + | The Bandsaws are owned by Joe and where in the lab since [[2014-05-01_Jour_Fixe]] but was removed in Feb 2016. |
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. | A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. | ||
| + | |||
| + | == Current Status == | ||
| + | |||
| + | * Bergin / Clarke CBS 355: 1780mm +-3mm x 6mm, 6 TPI | ||
| + | * '''NOT''' in working condition | ||
| + | ** See https://lists.metalab.at/pipermail/cnc/2014-May/000903.html | ||
| + | ** http://www.clarkeservice.co.uk/manuals/woodworker/cbs355.pdf | ||
== How to Operate == | == How to Operate == | ||
| + | |||
| + | * Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!) | ||
| + | ** See Repair Guide otherwise... | ||
| + | * Check if the band is OK | ||
| + | ** See Repair Guide otherwise.. | ||
| + | * Adjust the upper band holder to the correct hight (It should be right about your workpiece) | ||
| + | * Switch it on | ||
| + | * Saw | ||
| + | |||
| + | {{#ev:youtube|MBbFBf5t0Kk|320}} | ||
| + | |||
| + | === General Tips === | ||
| + | |||
| + | * Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside | ||
| + | * A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine | ||
| + | * The band swings in every direction a few parts of a mm. Consider that while you are sawing! | ||
== How to Repair == | == How to Repair == | ||
| + | |||
| + | There is a good guide how to correctly setup a bandsaw here: [http://www.1-2-do.com/forum/bandsaege-richtig-einstellen-thema-14087.html Bandsäge einstellen (German)] | ||
| + | |||
| + | Blades: | ||
| + | * http://www.hisi.at/produkte/sagebander/bimetall-sagebander/ | ||
| + | * http://www.ibh-werkzeuge.at/IBH/Holz_%26_Kunststoff.html | ||
| + | * http://www.albinkraus.at/en/1892520/Woodworking-Cutting-tools.html | ||
| + | * http://www.harton.co.at/index.aspx?show=schaerfdienst | ||
Aktuelle Version vom 27. August 2017, 19:43 Uhr
The Bandsaws are owned by Joe and where in the lab since 2014-05-01_Jour_Fixe but was removed in Feb 2016.
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
Current Status
- Bergin / Clarke CBS 355: 1780mm +-3mm x 6mm, 6 TPI
- NOT in working condition
How to Operate
- Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!)
- See Repair Guide otherwise...
- Check if the band is OK
- See Repair Guide otherwise..
- Adjust the upper band holder to the correct hight (It should be right about your workpiece)
- Switch it on
- Saw
General Tips
- Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside
- A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine
- The band swings in every direction a few parts of a mm. Consider that while you are sawing!
How to Repair
There is a good guide how to correctly setup a bandsaw here: Bandsäge einstellen (German)
Blades:
