GoCNC: Unterschied zwischen den Versionen
Pk (Diskussion | Beiträge) +bunt, Herstellerlink, History |
Navi (Diskussion | Beiträge) Replace core.png with actual address |
||
| (6 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt) | |||
| Zeile 4: | Zeile 4: | ||
|image=GoCNC A4Advanced.jpg | |image=GoCNC A4Advanced.jpg | ||
|owner=Metalab | |owner=Metalab | ||
|status= | |status=Gone? Pls direct pointers on whereabout to cnc list or core@metalab.at | ||
|requirestraining= | |requirestraining=yes | ||
|requiresauth=NOPE | |requiresauth=NOPE | ||
|cost= | |cost=900€ | ||
|teachers=contact cnc@lists.metalab.at | |teachers=contact cnc@lists.metalab.at | ||
}} | }} | ||
GoCNC is a small [[CNC-Fräse]] machine for milling in max A4 size. <br /><small>It was [http://geilomat.soup.io/post/357365039/Thank-you-Christoph-S-for-donating-a donated by Christoph S.] in Oct. 2013.</small> | GoCNC is a small [[CNC-Fräse]] machine for milling in max A4 size. <br /><small>It was [https://web.archive.org/web/20171230020807/http://geilomat.soup.io/post/357365039/Thank-you-Christoph-S-for-donating-a donated by Christoph S.] in Oct. 2013.</small> | ||
== Tech Specs == | == Tech Specs == | ||
* [http://gocnc.de/product_info.php?cPath=22&products_id=32&language=en&osCsid=0dccfe57673957c911a8047a827c84dd | * [CNC Milling machine GoCNC Hobby A4 Advanced] (dead link: http://gocnc.de/product_info.php?cPath=22&products_id=32&language=en&osCsid=0dccfe57673957c911a8047a827c84dd) | ||
* Steppers are set to 1.5A, 8 Microsteps | * Steppers are set to 1.5A, 8 Microsteps | ||
** It uses a Stepp2500a control board | ** It uses a Stepp2500a control board | ||
| Zeile 22: | Zeile 22: | ||
* Maximum Speed: around 1000mm/min | * Maximum Speed: around 1000mm/min | ||
* For use with Dremel or Proxxon Device as spindle | * For use with Dremel or Proxxon Device as spindle | ||
* It uses M10 threaded rods, which are quite bad... | * It uses M10 threaded rods, which are quite bad... | ||
* You can not put too much torque on the screws that hold the Z axis on the X axis - therefore the axis is not very stable. | |||
** If you fix the axis, the axis will be locked! | |||
== Configuration == | == Configuration == | ||
| Zeile 39: | Zeile 40: | ||
(just to give you one example ;)) | (just to give you one example ;)) | ||
== Maybe Updates == | |||
* Break out the Relais for the spindle, maybe little bit tricky because the control board is not very well fixated inside the box | |||
* Use connectors instead of soldering - same problem as with the geilomat | |||
* fix cable lengths because complete area cannot be reached | |||
* use a silent fan | |||
[[Kategorie:Maschinen]] | [[Kategorie:Maschinen]] | ||