AVRProgrammers: Unterschied zwischen den Versionen
Keine Bearbeitungszusammenfassung |
|||
| (19 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) | |||
| Zeile 15: | Zeile 15: | ||
|3 ||N/C | |3 ||N/C | ||
|- | |- | ||
|4 ||TX | |4 ||TX or GND | ||
|- | |- | ||
|5 ||CS | |5 ||CS | ||
|- | |- | ||
|6 ||RX | |6 ||RX or GND | ||
|- | |- | ||
|7 ||SCK | |7 ||SCK | ||
| Zeile 52: | Zeile 52: | ||
= Programmers = | = Programmers = | ||
== RS-232 programmer (ATtiny2313) == | |||
[[Bild:avrprog-rs232.jpg|thumb|200px|RS-232 (ATTiny2313) programmer]] | |||
This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end. | This programmer has a DB-9 serial port in one end and a 10-pin ISP header in the other end. | ||
Programmer type: | Programmer type: avr910<br/> | ||
Speed: 115200 | Speed: 115200 | ||
avrdude | '''NB!''' This programmer uses non-standard device codes for atmega48/88/168 (0x06, 0x07 and 0x08).<br/> | ||
To make it work, edit avrdude.conf: | |||
part | |||
id = "m168"; | |||
avr910_devcode = 0x08; | |||
Note: This programmer requires the target to be self-powered. | |||
=== avrdude command lines === | |||
Check connection: | |||
avrdude -P <serialport> -c avr910 -b 115200 -p atmega168 | |||
== USBasp programmer (stripboard) == | == USBasp programmer (stripboard) == | ||
[[Bild:avrprog-usbasp.jpg|thumb|200px|USBasp stripboard programmer]] | |||
This is a USB programmer built on a stripboard. It has a USB-B connector in one end an a 10-pin ISP header in the other end. | This is a USB programmer built on a stripboard. It has a USB-B connector in one end an a 10-pin ISP header in the other end. | ||
Programmer type: usbasp | Programmer type: usbasp<br/> | ||
Speed: default | Speed: default | ||
avrdude command lines: | === avrdude command lines === | ||
Check connection: | |||
avrdude -c usbasp -p atmega168 | avrdude -c usbasp -p atmega168 | ||
Example: Program Arduino NG bootloader: | |||
avrdude -c usbasp -p atmega168 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdf:m -U lfuse:w:0xff:m | avrdude -c usbasp -p atmega168 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdf:m -U lfuse:w:0xff:m | ||
avrdude -c usbasp -p atmega168 -U flash:w:ATmegaBOOT_168_ng.hex:i -U lock:w:0x0f:m | avrdude -c usbasp -p atmega168 -U flash:w:ATmegaBOOT_168_ng.hex:i -U lock:w:0x0f:m | ||
== [[ | == [[Avrprog-metaboard]] == | ||
[[Bild:avrprog-metaboard.jpg|thumb|200px|Metaboard AVRprog programmer]] | |||
A [[Metaboard]]-based programmer. | A [[Metaboard]]-based programmer. | ||
| Zeile 84: | Zeile 99: | ||
This programmer behaves exactly like the USBasp stripboard programmer. | This programmer behaves exactly like the USBasp stripboard programmer. | ||
[[ | In the current incarnation, this programmer is not as stable as the USBasp version. | ||
We need to figure this out, e.g. ask [[User:cs|Christian]] for advice. | |||
Symptoms are aborted operation during read or write. Usually it helps to try again and to run verify as a separate step. | |||
avrdude: error: wrong reading bytes b8 | |||
Note: This programmer has a bootloader on it, so it can be updated over USB. There is a jumper to enable the bootloader. This jumper must be '''off''' when using it as a programmer and '''on''' when accessing the bootloader. | |||
== [http://www.ladyada.net/make/usbtinyisp USBTinyISP] == | |||
The USBTinyISP from Lady Ada. | |||
FIXME: Safe vs. unsafe | |||
Check connection: | |||
avrdude -c usbtiny -p atmega168 | |||
== Any Arduino Board == | |||
see [[Benutzer:Mihi/Programming-attiny45-mit-arduino]] | |||
= Troubleshooting = | |||
Sometimes, the following happens: | |||
<tt> | |||
avrdude: erasing chip<br/> | |||
avrdude: error: programm enable: target doesn't answer. 1 | |||
</tt> | |||
This has shown to be caused by wrong crystal fuse settings, typically an issue when programming fresh chips. | |||
To fix, program all fuses first, before erasing the chip. | |||
[[Kategorie:Arduino]] | [[Kategorie:Arduino]] | ||