Laser/Parameters: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(Vom Laserrechner)
(4 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)
Zeile 4: Zeile 4:
 
'''<span style="color:red">Probably outdated, as the tube was replaced on 2024-02-02. Verify before cutting! And mark it in the table as verified'''</span>
 
'''<span style="color:red">Probably outdated, as the tube was replaced on 2024-02-02. Verify before cutting! And mark it in the table as verified'''</span>
  
 +
=== Wood ===
 
{| class="wikitable" style="text-align: center;"
 
{| class="wikitable" style="text-align: center;"
 
! Material
 
! Material
Zeile 11: Zeile 12:
 
! Engrave Power
 
! Engrave Power
 
! Comments
 
! Comments
 +
 +
|-
 +
|Plywood birch 3mm
 +
|10-35
 +
|95%
 +
|250
 +
|30
 +
|Does cut properly with 35mm/s but in some places <10mm/s are required.
 +
 
|-
 
|-
−
|Black granite
+
|Plywood for "engraving" vector lines
 +
|150
 +
|7.5-37.5%
 
|n/a
 
|n/a
 
|n/a
 
|n/a
−
|300
+
|See [[Laser/Parameters#Notes_on_engraving_vector_lines|below]]
−
|50%
+
|-
 +
 
 +
|Cork 5mm (Kork-Matte)
 +
|20m
 +
|100-100%
 +
|?
 +
|?
 
|
 
|
 
|-
 
|-
−
|Linen cloth
+
|}
−
|300
+
 
−
|70%
+
=== Plastics ===
−
|n/a
+
{| class="wikitable" style="text-align: center;"
−
|n/a
+
! Material
−
|
+
! Cut Speed (mm/s)
 +
! Cut Power
 +
! Engrave Speed (mm/s)
 +
! Engrave Power
 +
! Comments
 +
|-
 +
|Schildermaterial Laserply
 +
|100
 +
|75%
 +
|200
 +
|20%
 +
|vermutlich geht auch weniger Leistung oder Schneller
 +
 
 +
|-
 +
|Ikea PP Dosen
 +
|x
 +
|x
 +
|200
 +
|25
 +
|10mm Fokusabstand
 +
|-
 +
|}
 +
 
 +
=== Rubber===
 +
{| class="wikitable" style="text-align: center;"
 +
! Material
 +
! Cut Speed (mm/s)
 +
! Cut Power
 +
! Engrave Speed (mm/s)
 +
! Engrave Power
 +
! Comments
 +
|-
 +
|Latex black 0,4mm
 +
|55
 +
|100%
 +
|?
 +
|?
 +
|6mm Focus
 +
 
 +
|-
 +
 
 +
|}
 +
 
  
 +
=== Paper / Cardboard ===
 +
{| class="wikitable" style="text-align: center;"
 +
! Material
 +
! Cut Speed (mm/s)
 +
! Cut Power
 +
! Engrave Speed (mm/s)
 +
! Engrave Power
 +
! Comments
 
|-
 
|-
−
|Leather 3mm
+
|Buchbinderpappe 0,5mm
−
|13
+
|110
−
|65%
+
|98%
−
|n/a
+
|?
−
|n/a
+
|?
−
| Innenseite des Leders nutzen, Glatt auflegen.
+
|2023 maxvalue
 +
 
 
|-
 
|-
 
|Finnboard/Finnpappe 0,9mm
 
|Finnboard/Finnpappe 0,9mm
Zeile 40: Zeile 109:
 
|?
 
|?
 
|2024 maxvalue
 
|2024 maxvalue
 +
 
|-
 
|-
 
|Finnboard/Finnpappe 4mm
 
|Finnboard/Finnpappe 4mm
Zeile 48: Zeile 118:
 
|
 
|
 
|-
 
|-
−
|Buchbinderpappe 0,5mm
+
|}
−
|110
+
 
−
|98%
+
=== Fabrics ===
−
|?
+
{| class="wikitable" style="text-align: center;"
−
|?
+
! Material
−
|2023 maxvalue
+
! Cut Speed (mm/s)
 +
! Cut Power
 +
! Engrave Speed (mm/s)
 +
! Engrave Power
 +
! Comments
 
|-
 
|-
−
|Plywood birch 3mm
+
|Linen cloth
−
|10-35
+
|300
−
|95%
+
|70%
−
|250
+
|n/a
−
|30
+
|n/a
−
|Does cut properly with 35mm/s but in some places <10mm/s are required.
+
|
−
|-
+
 
−
|Ikea PP Dosen
 
−
|x
 
−
|x
 
−
|200
 
−
|30
 
−
|10mm Fokusabstand
 
 
|-
 
|-
 
|Polyesterstoff
 
|Polyesterstoff
Zeile 75: Zeile 143:
 
|?
 
|?
 
|Fokus ist schwierig...
 
|Fokus ist schwierig...
 +
 +
|}
 +
 +
=== Misc ===
 +
 +
{| class="wikitable" style="text-align: center;"
 +
! Material
 +
! Cut Speed (mm/s)
 +
! Cut Power
 +
! Engrave Speed (mm/s)
 +
! Engrave Power
 +
! Comments
 +
|-
 +
|Black granite
 +
|n/a
 +
|n/a
 +
|300
 +
|50%
 +
|
 +
 
|-
 
|-
 
|Spacecraft Multi Layer Insulation
 
|Spacecraft Multi Layer Insulation
Zeile 84: Zeile 172:
  
 
|-
 
|-
−
|Cork 5mm (Kork-Matte)
+
|Leather 3mm
−
|20m
+
|13
−
|100-100%
+
|65%
−
|?
 
−
|?
 
−
|
 
−
 
 
−
|-
 
−
|Plywood for "engraving" vector lines
 
−
|150
 
−
|7.5-37.5%
 
 
|n/a
 
|n/a
 
|n/a
 
|n/a
−
|See [[Laser/Parameters#Notes_on_engraving_vector_lines|below]]
+
| Innenseite des Leders nutzen, Glatt auflegen. Leder als Naturprodukt liefert unterschiedliche Ergebnisse. Nubuk Leder z.b. benötigt bei 2mm 13mms/70w
−
 
 
  
 
|-
 
|-
Zeile 107: Zeile 186:
 
| 80%
 
| 80%
 
| Fokus: 7mm
 
| Fokus: 7mm
 +
 
|}
 
|}
  

Version vom 19. Juni 2024, 20:57 Uhr

Language: English
Subpages:
Laser/Parameters hat keine Unterseiten.

Verified parameters for the 100W BRM lasercutter:
Probably outdated, as the tube was replaced on 2024-02-02. Verify before cutting! And mark it in the table as verified

Wood

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Plywood birch 3mm 10-35 95% 250 30 Does cut properly with 35mm/s but in some places <10mm/s are required.
Plywood for "engraving" vector lines 150 7.5-37.5% n/a n/a See below
Cork 5mm (Kork-Matte) 20m 100-100% ? ?

Plastics

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Schildermaterial Laserply 100 75% 200 20% vermutlich geht auch weniger Leistung oder Schneller
Ikea PP Dosen x x 200 25 10mm Fokusabstand

Rubber

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Latex black 0,4mm 55 100% ? ? 6mm Focus


Paper / Cardboard

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Buchbinderpappe 0,5mm 110 98% ? ? 2023 maxvalue
Finnboard/Finnpappe 0,9mm 77 100% ? ? 2024 maxvalue
Finnboard/Finnpappe 4mm 25 98% ? ?

Fabrics

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Linen cloth 300 70% n/a n/a
Polyesterstoff 150 70% ? ? Fokus ist schwierig...

Misc

Material Cut Speed (mm/s) Cut Power Engrave Speed (mm/s) Engrave Power Comments
Black granite n/a n/a 300 50%
Spacecraft Multi Layer Insulation 100 80% ? ? Can occasionally melt together again after cutting
Leather 3mm 13 65% n/a n/a Innenseite des Leders nutzen, Glatt auflegen. Leder als Naturprodukt liefert unterschiedliche Ergebnisse. Nubuk Leder z.b. benötigt bei 2mm 13mms/70w
Gravur: Eloxiertes Aluminium - - 120 80% Fokus: 7mm

Attraktor hat den gleichen Lasercutter, deren Wiki hat viele Parametervorschlaege.

Notes on engraving vector lines

When using the "cut" mode to scratch thin lines into a surface (say, outlines of fields in a board game, when the full board is cut through), the laser is moved at high speeds (say, 150mm/s) with low power, but slows down when lines are bent too tightly. This is where the minimum cut power shines: The cutter will reduce power as it speeds down, to avoid burning through the material. If you set the lower bound too low, lines will get lost where it slows down (because the effect on the material is not linear, and 1% may not do anything at all any more). If you set it too high, the prolonged exposure on a single spot can send the laser all through the material.

For test cuts, take a coarse and a fine sample from your picture.

A practical test file is slowdowntest, which has multiple colors to try out different settings, and lines of varying curvature to see the effects.

Abgerufen von „https://metalab.at/wiki/index.php?title=Laser/Parameters&oldid=77879“