Bandsaw: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springenReox (Diskussion | Beiträge) (Die Seite wurde neu angelegt: „The Metalab currently has 3 different Bandsaws. A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. ==…“) |
Reox (Diskussion | Beiträge) |
||
| Zeile 1: | Zeile 1: | ||
| − | The Metalab currently has 3 different Bandsaws. | + | The Metalab currently has 3 different Bandsaws. Two Bandsaws are from Joe since [[2014-05-01_Jour_Fixe]]. |
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. | A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. | ||
| + | |||
| + | == Current Status == | ||
| + | |||
| + | * Green Saw (Joe): Band is broken, otherwise useable | ||
| + | * Blue Saw (Joe): Operational, but band is a little bit rusty | ||
| + | * Blue Saw (Metalab): Upper and Lower Band holder is broken - not useable at all | ||
== How to Operate == | == How to Operate == | ||
| + | |||
| + | * Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!) | ||
| + | ** See Repair Guide otherwise... | ||
| + | * Check if the band is OK | ||
| + | ** See Repair Guide otherwise.. | ||
| + | * Adjust the upper band holder to the correct hight (It should be right about your workpiece) | ||
| + | * Switch it on | ||
| + | * Saw | ||
| + | |||
| + | === General Tips === | ||
| + | |||
| + | * Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside | ||
| + | * A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine | ||
| + | * The band swings in every direction a few parts of a mm. Consider that while you are sawing! | ||
== How to Repair == | == How to Repair == | ||
| + | |||
| + | There is a good guide how to correctly setup a bandsaw here: [http://www.1-2-do.com/forum/bandsaege-richtig-einstellen-thema-14087.html Bandsäge einstellen (German)] | ||
Version vom 10. Juni 2014, 09:31 Uhr
The Metalab currently has 3 different Bandsaws. Two Bandsaws are from Joe since 2014-05-01_Jour_Fixe.
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
Current Status
- Green Saw (Joe): Band is broken, otherwise useable
- Blue Saw (Joe): Operational, but band is a little bit rusty
- Blue Saw (Metalab): Upper and Lower Band holder is broken - not useable at all
How to Operate
- Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!)
- See Repair Guide otherwise...
- Check if the band is OK
- See Repair Guide otherwise..
- Adjust the upper band holder to the correct hight (It should be right about your workpiece)
- Switch it on
- Saw
General Tips
- Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside
- A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine
- The band swings in every direction a few parts of a mm. Consider that while you are sawing!
How to Repair
There is a good guide how to correctly setup a bandsaw here: Bandsäge einstellen (German)
