Witbox: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen| Zeile 10: | Zeile 10: | ||
}} | }} | ||
__TOC__ | __TOC__ | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | '''It is OK to use the printer as it is.''' | ||
| + | |||
| + | '''It is NOT OK to modify it in any way.''' | ||
| + | |||
| + | This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap. | ||
| + | |||
===Overview=== | ===Overview=== | ||
| Zeile 23: | Zeile 33: | ||
===How to use it=== | ===How to use it=== | ||
| − | Calibration | + | Calibration (before every job @ metalab) |
| + | |||
| + | Load / Change Filament if neccessary - Careful not to entangle the filament!! | ||
| + | |||
| + | Save your .gcode to the SD card | ||
| + | |||
| + | Start job from menu. | ||
| + | |||
| − | |||
| − | |||
| − | |||
| Zeile 37: | Zeile 51: | ||
{| class="wikitable" | {| class="wikitable" | ||
| − | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| | + | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| Speed !! width="100"| Temperature (°C) !! width="100"|Who tried this !! width="100"| Notes |
|- | |- | ||
| PLA Neon Green || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | | PLA Neon Green || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | ||
|- | |- | ||
| − | | PLA WHITE (no | + | | PLA WHITE (no name big spool) || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Looks better at higher temperature |
|- | |- | ||
| PLA Black bq || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | | PLA Black bq || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | ||
| Zeile 55: | Zeile 69: | ||
{| class="wikitable" | {| class="wikitable" | ||
| − | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| | + | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| Speed !! width="100"|Temperature (°C) !! width="100"|Who tried this !! width="100"| Notes |
|- | |- | ||
| WHAT? || LAYER? ||SPEED|| TEMPERATURE || [[Benutzer:you|you]] || COMMENTS | | WHAT? || LAYER? ||SPEED|| TEMPERATURE || [[Benutzer:you|you]] || COMMENTS | ||
| Zeile 61: | Zeile 75: | ||
|} | |} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| Zeile 96: | Zeile 95: | ||
** [https://blog.adafruit.com/2014/12/04/bq-witbox-review-by-tom-3dthursday-3dprinting/ Adafruit article] | ** [https://blog.adafruit.com/2014/12/04/bq-witbox-review-by-tom-3dthursday-3dprinting/ Adafruit article] | ||
** [https://chopmeister.blogspot.cz/2014/08/sifting-through-features-or-guide-to.html 'Sifting through the features or "The Guide to Not Buying a 3D Printer"']. | ** [https://chopmeister.blogspot.cz/2014/08/sifting-through-features-or-guide-to.html 'Sifting through the features or "The Guide to Not Buying a 3D Printer"']. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | ===TODOs=== | ||
| + | |||
| + | Setup raspberry pi with octoprint | ||
| + | |||
| + | Design camera mount | ||
| + | |||
| + | Mount camera | ||
Version vom 30. Oktober 2015, 16:28 Uhr
3D-Scanner - CNC-Fräse - Laser - Reflow Oven - 3DPrinter (Prusa Mk2.5S, Prusa Mk3S, Prusa Mini) - Vinylplotter - Schweißinverter -Tischbohrmaschine - Drehbank - Ultraschallreiniger - Nähmaschinen
| Sprache: | Deutsch |
|---|
Subpages:
Witbox hat keine Unterseiten.
| Witbox | |
| |
| Eigentümer: | Metalab |
| Status: | Aktiv |
| Erfordert Einschulung: | Ja |
| Erfordert Authentisierung: | Ja |
| Kostet: | 0.10 euro / gram |
| Hilfsbereite: | |
It is OK to use the printer as it is.
It is NOT OK to modify it in any way.
This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap.
Overview
Filament diameter 1.75mm
Layer height: 0.05-0.25 mm (0.2 is fast and looks good)
Material: PLA only
Firmware version: ???
This machine was sponsored (better price) from 3dee.at
How to use it
Calibration (before every job @ metalab)
Load / Change Filament if neccessary - Careful not to entangle the filament!!
Save your .gcode to the SD card
Start job from menu.
Wisdom Tables
These settings have been tested and worked fine. ✔
| MATERIAL | Layer height | Speed | Temperature (°C) | Who tried this | Notes |
|---|---|---|---|---|---|
| PLA Neon Green | 0.1mm | 80mm/sec | 210C | overflo | Good. |
| PLA WHITE (no name big spool) | 0.1mm | 80mm/sec | 210C | overflo | Looks better at higher temperature |
| PLA Black bq | 0.1mm | 80mm/sec | 210C | overflo | Good. |
| PLA transparent bq | 0.1mm | 80mm/sec | 210C | overflo | Good. |
| PLA purple noname (3dee.at) | 0.1mm | 80mm/sec | 210C | overflo | Good. |
These settings caused some problems ✘
| MATERIAL | Layer height | Speed | Temperature (°C) | Who tried this | Notes |
|---|---|---|---|---|---|
| WHAT? | LAYER? | SPEED | TEMPERATURE | you | COMMENTS |
Software
Supporters
Diverse Links
- Design of the 3D-Printer is under CreativeCommons licence.
- heise.de comparsion of different printers (German) (pro for our use: we can buy replacement parts easily in Vienna)
- Review of the printer (German)
- Other reviews (english):
TODOs
Setup raspberry pi with octoprint
Design camera mount
Mount camera
