Umbrella: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(Version 2.0 incoming)
(47 dazwischenliegende Versionen von 9 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
−
infos zum metalights projekt.
+
__TOC__
 +
=Version 2.0=
 +
At several [[Jour_Fixe|Jour fixes]] ([[2022-02-22_Jour_Fixe#neues_Licht_im_Hauptraum_.28luto.2C_cube.2C_anlumo.29|2022-02-22_Jour_Fixe]], [[2022-04-26_Jour_Fixe#Upgrade_f.C3.BCr.27s_Upgrade_vom_Hauptraumlicht_.28ripper.2C_anlumo.2C_cube.2C_nicht_luto.29|2022-04-26_Jour_Fixe]] and [[2022-05-11_Jour_Fixe#Erhellung_Hauptraum_.28ripper.2C_fussel.29|2022-05-11_Jour_Fixe]]) the decision was made that the Umbrellas need an upgrade. The LED strips will be replaced by four IKEA Tradfri LED bulbs which are mounted on a custom lasercut aluminium plate.
 +
[[Datei:Umbrella_v2_4er.png|300px|thumb|right|3D redering of the Aluminium plate with the LED bulbs]]
  
 +
=Version 1.0=
 +
This will be obsolete soon.
 +
[[Datei:Buntschirm.jpg|right|miniatur]]
 +
[[Datei:u_blue.jpg|right|miniatur]]
 +
[[Datei:u_pink.jpg|right|miniatur]]
 +
 +
Umbrella is the ceiling lighting of the main room. It consist out of 12 umbrellas capable of emitting light in either 16581375 RGB shades or 65025 white shades.
  
−
==Why==
+
The umbrellas are controllable with [https://en.wikipedia.org/wiki/Art-Net art-net].
  
−
The metalab needed some new lights.
 
  
−
ARTnet is the name of the game.
+
==How to simply turn on/off the light==
  
−
== How ==
+
Use the '''[[Interruttore/en|Interruttore]]''' light switch.
 +
 
 +
== Access data ==
  
 +
* WLAN SSID: metalights
 +
* Protocol: [https://en.wikipedia.org/wiki/Art-Net art-net]
 +
* Host: 10.20.255.255
 +
* startUniverse: 3
 +
* There are 60 channel, 5 channels (RGBWW) per umbrella.
  
−
Raspberry Pi 3
 
  
−
Hostapd for Accesspoint mode
+
== Why ==
 +
 +
The Metalab needed some new lights. ART-net is awesome.
  
−
QLC+ headless build
+
 +
== How ==
 +
 +
* Raspberry Pi 3 + Touchscreen
 +
* Distro based on the QLC+ image (raspbian jessie)
 +
* QLC+ XServer less build that renders directly in GL buffers for performance
 +
* H801 based clients (ESP8266)
 +
* Arduino based firmware that implements ART-net
  
−
Various H801 based clients (ESP8266)
 
  
 +
== Temporary setup with QLC+ ==
 +
 +
* Connect to "metalights" WLAN
 +
* Set OUTPUT to 10.20.255.255
 +
* Set ARTnet universe to 3
 +
* There are 5 channels / Umbrella
 +
* R,G,B,WW,CW
 +
* If CW or WW are anything else but "0" then R,G and B are disabled by firmware.
 +
* If R,G or B are anything but "0" then CW and WW are disabled by firmware.
 +
* This is to save our power supplies from sudden heat death.
 +
* (105 watt / Umbrella max)
 +
  
−
==Who==
+
== Hardware ==
 +
 +
H801 LED controller features:
 +
* 8 Mbit Storage (1 Mb)
 +
* 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel)
 +
  
−
Originally invented and built by [[Benutzer:overflo|overflo]], the project is not maintened by:
+
=== How to flash ===
  
−
<insert name here>
+
* Install [https://www.arduino.cc/en/Main/Software Arduino IDE]
 +
* Install [http://esp8266.github.io/Arduino/versions/2.0.0/doc/installing.html ESP 8266 extensions]
 +
* Choose generic ESP8266 Board under Tools->Board
 +
* Settings for ESP8266:  [[File:Umbrella_address.png|300px|right]]
 +
** GENERIC ESP8266 Module
 +
** Flash Mode: DIO
 +
** Flash Size: 1M (512K SPIFFS)
 +
** Debug Port: Disabled
 +
** Debug Level: none
 +
** Reset Mode: ck
 +
** Flash Frequency: 40 MHz
 +
** CPU Frequency: 80 MHz
 +
** Upload Speed: 115200 or more
 +
  
 +
* U need a USB-to-UART-board (set to 3.3V)
 +
* Connect GND to GND; RX to TX(!) and TX to RX(!); DO NOT CONNECT 3.3V!
 +
* Set JUMPER on board to boot into flash mode. (Important! Has to be set before power is connected, so board gets into flashing mode.)
 +
* Supply power via VCC & GND (12V should be adequate)
 +
 +
The code to flash can be found in the [https://github.com/overflo23/H801_ARTnet github repo].
 +
If you want to flash exactly this code (and what else would you flash in the main room), you will need these libraries:
  
−
Please contact anyone from the list above for questions regarding the metalabs light setup.
+
* [https://github.com/rstephan/ArtnetWifi ArtnetWifi] (Has to be installed via git clone to ~/Arduino/libraries)
 +
* [https://github.com/tzapu/WiFiManager WifiManager]
 +
* [https://arduinojson.org/ ArduinoJson] (Version 5.13.3)
  
  
 +
== Who ==
 +
 +
Originally invented and built by [[Benutzer:overflo|overflo]], the umbrellas were built by a lot of people in some night shifts at Metalab
 +
 +
LOTS of support by
 +
* uniq, anlumo, ripper, bogdan <your name here>
  
  
−
==Links==
+
== QLC+ ==
  
 +
* Neue Fixture: [[Datei:Hauptraum_setup.qxw.txt]] (das muss nach ~/.qlcplus/fixtures/hauptraum-setup.qxf)
 +
* Fixture: [[Datei:Metalab-Umbrella.txt]] (das muss nach ~/.qlcplus/fixtures/Metalab-Umbrella.qxf)
 +
* Demo Desk: [[Datei:Test.txt]]
  
−
[http://www.qlcplus.org/ QLC+]
 
  
−
[https://de.aliexpress.com/item/DC5-24V-Wireless-Smart-Dimmer-Receiver-Output-5-Routes-PWM-Data-WiFi-APP-Controlled-for-RGBW H801]
+
== Links ==
  
−
[https://github.com/overflo23/H801_ARTnet Github]
+
* [http://www.qlcplus.org/ QLC+]
 +
* [http://tinkerman.cat/closer-look-h801-led-wifi-controller H801]
 +
* [https://github.com/overflo23/H801_ARTnet Github]
 +
* [http://www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf ART-net Reference]
 +
 +
[[Artnet]]
 +
* [https://github.com/reox/pybrella A Python implementation to control the umbrellas]

Version vom 16. Juni 2022, 21:09 Uhr

Version 2.0

At several Jour fixes (2022-02-22_Jour_Fixe, 2022-04-26_Jour_Fixe and 2022-05-11_Jour_Fixe) the decision was made that the Umbrellas need an upgrade. The LED strips will be replaced by four IKEA Tradfri LED bulbs which are mounted on a custom lasercut aluminium plate.

3D redering of the Aluminium plate with the LED bulbs

Version 1.0

This will be obsolete soon.

Buntschirm.jpg
U blue.jpg
U pink.jpg

Umbrella is the ceiling lighting of the main room. It consist out of 12 umbrellas capable of emitting light in either 16581375 RGB shades or 65025 white shades.

The umbrellas are controllable with art-net.


How to simply turn on/off the light

Use the Interruttore light switch.

Access data

  • WLAN SSID: metalights
  • Protocol: art-net
  • Host: 10.20.255.255
  • startUniverse: 3
  • There are 60 channel, 5 channels (RGBWW) per umbrella.


Why

The Metalab needed some new lights. ART-net is awesome.


How

  • Raspberry Pi 3 + Touchscreen
  • Distro based on the QLC+ image (raspbian jessie)
  • QLC+ XServer less build that renders directly in GL buffers for performance
  • H801 based clients (ESP8266)
  • Arduino based firmware that implements ART-net


Temporary setup with QLC+

  • Connect to "metalights" WLAN
  • Set OUTPUT to 10.20.255.255
  • Set ARTnet universe to 3
  • There are 5 channels / Umbrella
  • R,G,B,WW,CW
  • If CW or WW are anything else but "0" then R,G and B are disabled by firmware.
  • If R,G or B are anything but "0" then CW and WW are disabled by firmware.
  • This is to save our power supplies from sudden heat death.
  • (105 watt / Umbrella max)


Hardware

H801 LED controller features:

  • 8 Mbit Storage (1 Mb)
  • 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel)


How to flash

  • Install Arduino IDE
  • Install ESP 8266 extensions
  • Choose generic ESP8266 Board under Tools->Board
  • Settings for ESP8266:
    Umbrella address.png
    • GENERIC ESP8266 Module
    • Flash Mode: DIO
    • Flash Size: 1M (512K SPIFFS)
    • Debug Port: Disabled
    • Debug Level: none
    • Reset Mode: ck
    • Flash Frequency: 40 MHz
    • CPU Frequency: 80 MHz
    • Upload Speed: 115200 or more


  • U need a USB-to-UART-board (set to 3.3V)
  • Connect GND to GND; RX to TX(!) and TX to RX(!); DO NOT CONNECT 3.3V!
  • Set JUMPER on board to boot into flash mode. (Important! Has to be set before power is connected, so board gets into flashing mode.)
  • Supply power via VCC & GND (12V should be adequate)

The code to flash can be found in the github repo. If you want to flash exactly this code (and what else would you flash in the main room), you will need these libraries:


Who

Originally invented and built by overflo, the umbrellas were built by a lot of people in some night shifts at Metalab

LOTS of support by

  • uniq, anlumo, ripper, bogdan <your name here>


QLC+


Links

Artnet

Abgerufen von „https://metalab.at/wiki/index.php?title=Umbrella&oldid=72312“