Umbrella: Unterschied zwischen den Versionen
(→QLC+) |
|||
| (28 dazwischenliegende Versionen von 5 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| − | + | [[Datei:Buntschirm.jpg|miniatur]] | |
| + | [[Datei:u_blue.jpg|miniatur]] | ||
| + | [[Datei:u_pink.jpg|miniatur]] | ||
| + | |||
| + | Umbrella is the ceiling lighting of the main room. It consist out of 12 umbrellas capable of emitting light in either 16581375 RGB shades or 65025 white shades. | ||
| + | The umbrellas are controllable with [https://en.wikipedia.org/wiki/Art-Net art-net]. | ||
| + | |||
| + | ==How to simply turn on/off the light== | ||
| + | Use the light switch next to the kitchen. You can dim the light with the rotary knob on the side. | ||
| + | |||
| + | |||
| + | [[Datei:Umbrella_lightswitch_1.jpg|200px]] | ||
| + | [[Datei:Umbrella_lightswitch_2.jpg|200px]] | ||
| + | |||
| + | If it does not work just power cycle it. Wait a couple of seconds. | ||
| − | == | + | [[Datei:Umbrella_reset.jpg|200px|Metalab school of software resilience(tm) :)]] |
| + | |||
| + | ==Access data== | ||
| − | + | Wlan SSID: metalights | |
| − | + | Protocol: [https://en.wikipedia.org/wiki/Art-Net art-net] | |
| + | Host: 10.20.255.255 | ||
| − | + | startUniverse: 3 | |
| − | + | There are 60 channel, 5 channels (RGBWW) per umbrella. | |
| + | ==Why== | ||
| + | |||
| + | The Metalab needed some new lights. | ||
| + | |||
| + | ART-net is awesome. | ||
| + | |||
| + | |||
| + | == How == | ||
| + | |||
| + | Raspberry Pi 3 + Touchscreen | ||
| + | |||
Distro based on the QLC+ image (raspbian jessie) | Distro based on the QLC+ image (raspbian jessie) | ||
| − | + | ||
| − | + | QLC+ XServer less build that renders directly in GL buffers for performance | |
| − | + | ||
| − | QLC+ | ||
| − | |||
H801 based clients (ESP8266) | H801 based clients (ESP8266) | ||
| − | + | ||
Arduino based firmware that implements ART-net | Arduino based firmware that implements ART-net | ||
| − | + | ||
| − | + | == Temporary setup with QLC+ == | |
| − | == | + | |
| − | + | Connect to "metalights" WLAN | |
| − | + | ||
| − | + | Set OUTPUT to 10.20.255.255 | |
| − | + | ||
| − | + | Set ARTnet universe to 3 | |
| − | + | ||
| − | + | There are 5 channels / Umbrella | |
| − | + | ||
| − | + | R,G,B,WW,CW | |
| − | + | ||
| − | + | If CW or WW are anything else but "0" then R,G and B are disabled by firmware. | |
| − | + | ||
| − | + | If R,G or B are anything but "0" then CW and WW are disabled by firmware. | |
| − | + | ||
| − | + | This is to save our power supplies from sudden heat death. | |
| − | + | ||
| + | (105 watt / Umbrella max) | ||
| + | |||
| + | |||
== Hardware == | == Hardware == | ||
| − | + | ||
| − | H801 | + | H801 LED controller features: |
| − | + | ||
* 8 Mbit Storage (1 Mb) | * 8 Mbit Storage (1 Mb) | ||
* 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel) | * 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel) | ||
| + | |||
| − | == | + | === How to flash === |
| + | * Install [https://www.arduino.cc/en/Main/Software Arduino IDE] | ||
| + | * Install [http://esp8266.github.io/Arduino/versions/2.0.0/doc/installing.html ESP 8266 extensions] | ||
| + | * Choose correct Board under Tools->Board | ||
| + | * Settings for ESP8266: [[File:Umbrella_address.png|300px|right]] | ||
| + | ** GENERIC ESP8266 Module | ||
| + | ** Flash Mode: DIO | ||
| + | ** Flash Size: 1M (512K SPIFFS) | ||
| + | ** Debug Port: Disabled | ||
| + | ** Debug Level: none | ||
| + | ** Reset Mode: ck | ||
| + | ** Flash Frequency: 40 MHz | ||
| + | ** CPU Frequency: 80 MHz | ||
| + | ** Upload Speed: 115200 or more | ||
| + | |||
| + | |||
| + | * Set JUMPER on board to boot into flash mode. | ||
| + | * Power up the board. | ||
| + | |||
| − | + | A successfully tested art-net library for ESP is [[ArtnetWifi]] | |
| − | < | + | ==Who== |
| + | |||
| + | Originally invented and built by [[Benutzer:overflo|overflo]], the umbrellas were built by a lot of people in some night shifts at Metalab | ||
| + | |||
| + | LOTS OF SUPPORT BY | ||
| + | uniq, anlumo, ripper, bogdan <your name here> | ||
| + | |||
| + | == QLC+ == | ||
| − | |||
| + | Neue Fixture: [[Datei:Hauptraum_setup.qxw.txt]] (das muss nach ~/.qlcplus/fixtures/hauptraum-setup.qxf) | ||
| + | Fixture: [[Datei:Metalab-Umbrella.txt]] (das muss nach ~/.qlcplus/fixtures/Metalab-Umbrella.qxf) | ||
| + | Demo Desk: [[Datei:Test.txt]] | ||
==Links== | ==Links== | ||
| − | + | ||
| − | |||
[http://www.qlcplus.org/ QLC+] | [http://www.qlcplus.org/ QLC+] | ||
| − | + | ||
| − | [https://de.aliexpress.com/item/DC5-24V-Wireless-Smart-Dimmer-Receiver-Output-5-Routes-PWM-Data-WiFi-APP-Controlled-for-RGBW H801] | + | [https://de.aliexpress.com/item/DC5-24V-Wireless-Smart-Dimmer-Receiver-Output-5-Routes-PWM-Data-WiFi-APP-Controlled-for-RGBW H801 Controllers] |
| − | + | ||
[https://github.com/overflo23/H801_ARTnet Github] | [https://github.com/overflo23/H801_ARTnet Github] | ||
| − | + | ||
[http://www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf ART-net Reference] | [http://www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf ART-net Reference] | ||
| + | |||
| + | [[Artnet]] | ||
Version vom 29. Juni 2018, 16:06 Uhr
Umbrella is the ceiling lighting of the main room. It consist out of 12 umbrellas capable of emitting light in either 16581375 RGB shades or 65025 white shades.
The umbrellas are controllable with art-net.
How to simply turn on/off the light
Use the light switch next to the kitchen. You can dim the light with the rotary knob on the side.
If it does not work just power cycle it. Wait a couple of seconds.
Access data
Wlan SSID: metalights
Protocol: art-net
Host: 10.20.255.255
startUniverse: 3
There are 60 channel, 5 channels (RGBWW) per umbrella.
Why
The Metalab needed some new lights.
ART-net is awesome.
How
Raspberry Pi 3 + Touchscreen
Distro based on the QLC+ image (raspbian jessie)
QLC+ XServer less build that renders directly in GL buffers for performance
H801 based clients (ESP8266)
Arduino based firmware that implements ART-net
Temporary setup with QLC+
Connect to "metalights" WLAN
Set OUTPUT to 10.20.255.255
Set ARTnet universe to 3
There are 5 channels / Umbrella
R,G,B,WW,CW
If CW or WW are anything else but "0" then R,G and B are disabled by firmware.
If R,G or B are anything but "0" then CW and WW are disabled by firmware.
This is to save our power supplies from sudden heat death.
(105 watt / Umbrella max)
Hardware
H801 LED controller features:
- 8 Mbit Storage (1 Mb)
- 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel)
How to flash
- Install Arduino IDE
- Install ESP 8266 extensions
- Choose correct Board under Tools->Board
- Settings for ESP8266:
- GENERIC ESP8266 Module
- Flash Mode: DIO
- Flash Size: 1M (512K SPIFFS)
- Debug Port: Disabled
- Debug Level: none
- Reset Mode: ck
- Flash Frequency: 40 MHz
- CPU Frequency: 80 MHz
- Upload Speed: 115200 or more
- Set JUMPER on board to boot into flash mode.
- Power up the board.
A successfully tested art-net library for ESP is ArtnetWifi
Who
Originally invented and built by overflo, the umbrellas were built by a lot of people in some night shifts at Metalab
LOTS OF SUPPORT BY uniq, anlumo, ripper, bogdan <your name here>
QLC+
Neue Fixture: Datei:Hauptraum setup.qxw.txt (das muss nach ~/.qlcplus/fixtures/hauptraum-setup.qxf)
Fixture: Datei:Metalab-Umbrella.txt (das muss nach ~/.qlcplus/fixtures/Metalab-Umbrella.qxf)
Demo Desk: Datei:Test.txt
