Laser/Hacking: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
Zeile 40: Zeile 40:
  
 
<code>
 
<code>
<nowiki>
+
<pre>
 
< 0x69 (i)
 
< 0x69 (i)
 
< 0x34 (4)
 
< 0x34 (4)
Zeile 68: Zeile 68:
 
> 0x0a
 
> 0x0a
 
> 0x14
 
> 0x14
</nowiki>
+
</pre>
 
</code>
 
</code>
  

Version vom 4. April 2021, 16:24 Uhr

For now just a unorganized pastebin to document things that don't fit the mastodon account.

Device resolutions

Resolution Width Height
Physical   1300 mm   900 mm
Cut 13000 positions  9000 positions
Engrave 51181 points 35433 points

Instructions

Cutting

tbd

Engraving

tbd

Rotary Engraving

Get the rotate engrave tool and put it in the lasercutter (in a way where the wide side faces you). Align it to the X axis of the lasercutter. Connect the two cables to the two plugs on the upper right side of the inner workarea (labeled 'rotation'). Flick the Axis Y/Axis U switch on the side of the lasercutter to the 'Axis U' position. Turn the lasercutter on. Test if everything is working by moving the y axis. If the rotate engrave tool moves you're good to go. Move the laser over the object you want to engrave. Be sure that you are exactly in the middle of the object on the y axis. If the laser hits the object, press reset, the laser will move the z axis down. Repeat as many times as needed. In the driver software, enable rotate engrave in the 'Output' Tab. Set circle pulse to 7600 and enter the diameter of the object. Enter the speed an press 'Test'. Ensure that the object does not fall after rotating 360°. Proceed as you would normally when engraving.

Reverse Engineering

Driver (LaserWorks aka RDCAM)

Nope.

Communication Protocol

The protocol can be used in 3 ways.

  • USB
  • Network
  • By saving the job to a file in the driver.

We didn't get the net- to work (haha) so we are using USB right now.

Setup Messages

Before sending the job to the lasercutter the driver sends and receives a few preflight messages. We are unsure if the change when using the Network but they are omitted when saving a job to a file.


Click 'Search'

< 0x69 (i)
< 0x34 (4)
< 0xb8
< 0x4e (N)
> 	0x69 (i)
> 	0xb4
> 	0xb8
> 	0x4e (N)
> 	0x36 (6)
> 	0x2c (,)
> 	0xb4
> 	0x76 (v)
> 	0x34 (4)

< 0x69 (i)
< 0x34 (4)
< 0x34 (4)
< 0x84
> 	0x69 (i)
> 	0xb4
> 	0x34 (4)
> 	0x84
> 	0x34 (4)
> 	0xb2
> 	0xd4
> 	0x0a
> 	0x14

Select COM Device

< 0x69 (i) < 0x34 (4) < 0x34 (4) < 0x24 ($) > 0x69 (i) > 0xb4 > 0x34 (4) > 0x24 ($) > 0x34 (4) > 0x34 (4) > 0xb4 > 0x74 (t) > 0x34 (4)

Laserfirmware

Nope.