Laser/How to Lazzzor: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(+cat)
(note on using inkscape and FreeCAD for DXF Export)
 
(95 dazwischenliegende Versionen von 11 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
== How to Lazzzor or "Why your mother doesn't use scissors anymore." ==
+
{{Languages|en}}
  
 +
== How to Lazzzor or "Why you won't use scissors anymore." ==
  
'''this is a very very early draft for a yet-to-come howto lazzor page. the main source of information was todays (27.1.11) lazzor workshop. feel free to add/edit some more information, suggestions or similar. you can do that in english or german. also it doesnt need to be perfect, but information supplied should be correct or if not, labled accordingly'''
+
=== Before you begin you should know.. ===
 +
{|
 +
|bgcolor="#ffff99"|<div style="border:2px dotted #00cce4;color:black;line-height:1.1em;padding:1em;">
 +
'''DO NOT HANDLE THE LAZZZOR IF YOU ARE NOT AUTHORIZED TO'''.
  
 +
Only [[Lazzzorauth]] key owners are able to operate the mighty Lazzzor. If you are authorized as well '''because you've successfully completed a [[Lazzzor_Cutter_Workshop]] _AND_ you've been given approval by one of the [http://metalab.at/wiki/Lazzzor#Willst_du_etwas_lasern.3F laser admins]''' you may request your own [[Lazzzorauth]] iButton.
  
so, you want to use the mighty fine lazzzor yesyes?
 
then you will have to complete several trials to step up to the throne of beeing a lazzzor king or queen.
 
  
basically, you have 2 options:
+
'''All others will need a assisting* key owner that is responsible for safe operation.'''</div>
* cutting: for this you need a vector picture (ugh find another word?),
+
|}
* engraving: for this you need a rasterized picture,
 
  
you are also able to do '''both!''' if you put a rasterized object inside a vector picture.
+
Amongst others some friendly helpers are:
alternatively you can make a file for each job.
+
{{Lasermenschen}}
  
=== prepare your motive. ===
+
----
 +
So, you want to use the mighty fine lazzzor yesyes?
 +
Then you will have to complete several trials to step up to the throne of being a lazzzor king or queen.
  
get your favorite vector/raster drawing program and draw some stuff you like
+
Basically, you have 2 options:
to have cut or engraved.
+
* '''cutting''': for this you need a vector graphic,
 +
* '''engraving''': for this you need a raster image
  
depending on what you want to do,
+
You can also do '''both!''' if you put a rasterized object inside a vector graphic. Alternatively you can create a separate file for each job.
your motive is qualified for print if the following things apply.
 
  
cutting / vector format:
+
== prepare your image ==
* deactivate filling on all objects
 
* set the stroke width on all objects to 0
 
* export your picture in *.eps format [.. other recommended formats]
 
** we strongly encourage you NOT to use dxf formats. they are prone to errors when imported into corel draw.
 
* during exporting/saving, look for an option which says "Make a bounding box around full page" or similar and DEactivate it.
 
  
engraving / raster format:
+
Get your favorite vector/raster drawing program and draw some stuff you want to have cut or engraved. Depending on what you want to do, your image file is qualified for print if the following things apply.
* convert your motive to grayscale
 
* play around with the Level option to get as high contrast as possible
 
* you can set the DPI for your motive up to 1200 (max. setting the lazzzor supports)
 
* no background color (means: transparent)
 
 
 
 
 
software recommendations: ...
 
 
 
 
 
=== the printer dialog ===
 
 
 
* main tab
 
Power: how much power to put into each lazzzor shot.
 
for cutting, you want to use as little power as possible
 
 
 
Speed: how fast the lazzzor move.
 
 
 
Frequency: how many times a lazzzor shot happens.
 
this depends greatly on the material used.
 
 
 
raster: for engraving
 
vector: for cutting
 
combined: for doing both! engraving always comes first.
 
 
 
rasterisation:--
 
basic: makes it look good, most of the time youll want to use this.
 
3D: good for making stuff like holes for screws.
 
stamp: yeah, thats for stamps, there are also 2 additional parameters for this one.
 
 
 
misc:--
 
Autofokus: important for making good cuts, you also can do that manually (todo)
 
Frequency automatic: not tested yet! but it obviously states what it does, yes?
 
Vector Sorting: algorithem which should calculate a good way to cut stuff.
 
you probably should do a good motive instead of relying on this, but
 
most of the time it shouldnt cause any problems.
 
 
 
* user settings
 
here you can load some saved settings created by other users.
 
warning! this doesnt mean they are automagically the best choice,
 
in some cases quite the opposite is the case and you might
 
end up damaging your material or the lazzzor.
 
still, in combination with the cheat sheet included in the manual,
 
you can figure out if there are some reasonable settings too.
 
 
 
* colormapping
 
depending which colors you gave your vectors, you can set individual
 
power, speed and frequency settings for each color! might come in handy,
 
most of the time it doesnt though.
 
 
 
 
 
=== the materials ===
 
if you want to cut / engrave something, bring your material, though
 
you can also use any leftovers or stuff which does not have a label on it.
 
(of course labels which says "free for all" are ok too).
 
feel free to donate a little extra if you use some materials.
 
(price, costs, material category?)
 
 
 
allowed:
 
cutting / engraving:
 
* anything made out of wood
 
* acryl
 
* polypropylene
 
* polystyrol (low power&speed!)
 
* fabric (hm what about polyester?)
 
* ...
 
* very very thin metals (foil or curcuit board made out of Messing)  (--> indepth howto at example page?)
 
 
 
engraving:
 
* glass
 
* ...
 
 
 
forbidden:
 
anything which got Chlor or Stickstoff in it. bad stuff will happen if it combusts.
 
some examples:
 
* PVC
 
* PC
 
* Polyurethan
 
 
 
other potential dangerous stuffs:
 
* BoPET Foil: as used in rescure blankets. has the ability to reflect big part of the IR spectrum. omg.
 
* ...
 
 
 
 
 
should some materials be forbidden which are already used? --> http://entropie.digital.udk-berlin.de/wiki/Laser_Cutter#FORBIDDEN_MATERIALS
 
 
 
=== to the lazzzor! ===
 
you have sent your job to the lazzzor and chosen your material of choice,
 
now off you go my friend, you are a big boy now, but still,
 
there are some buttons you have to get familiar with first.
 
(pwetty pictures!)
 
 
 
2 important buttons:
 
* "Go" aka Green Button aka "yea go that."
 
* "Stop" aka Red Button aka "no way, dont do that."
 
 
 
==== how to set your 0-point. ====
 
its a good idea to set your home-point everytime before a different job.
 
this point is the starting position and represents the upper left corner
 
in your picture / workspace area.
 
 
 
1. press "Pointer" (or what was it?) to make it visible/invisible
 
2. press "X/Y", the display will say "X/Y - Off"
 
3. you can now move the lazzzor freely along its x and y axis
 
4. press "Set-Home" to set your position as your home-point.
 
 
 
IMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANT
 
before you start a job ALWAYS TURN ON THE BELÜFTUNG (picture)
 
IMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANT
 
 
 
and before you start your job read..
 
==== when to cancel/pause your job! ====
 
if you ...
 
* .. hear noises you are not used to hear
 
* .. see smoke gathering in the cutting area
 
* .. see something burning constantly. (one or two spurts of flame are okay when cutting acryl (i think it was acryl?))
 
 
 
now now, go on, push teh button!..
 
==== how to start, pause and stop your job! ====
 
most of the buttons concerning jobs are obviously labeled, though, a explaination shall commence.
 
 
 
1. (todo)
 
2.
 
 
 
 
 
=== taking care of the lazzor: ===
 
 
 
* if you think your settings are pretty much okay but it still wont cut through then there is a possibility that the lazzzor needs some cleaning.
 
 
 
 
 
=== possible misc ideas: ===
 
* die klappe besser abdichten mit nem gummi oder so.. auch praktisch beim zumachen damits nicht zukrachen bzw zerbrechen kann
 
* tatsächliche schadstoffe in der luft messen, was für ein gerät braucht man da? interessant wärs schon
 
  
 +
'''for both''': your image/graphic should fit into the workspace which is '''1300mmx900mm''' big.
 +
'''Cutting / Vector format''':
 +
* deactivate filling on all objects
 +
* set the stroke width on all objects to 0.001 inch (or hairline)
 +
<strike>** watch out for duplicated vectors lying on top of each other. it results in the line being cut twice.</strike> [[Ctrl-Cut]] automatically handles duplicate lines.
 +
* export your model in pdf format (it is also possible to use ai, ps, eps, ctrl-cut vector format and svg, but pdf is highly recommended).
 +
* If you use FreeCAD to export SVG, make sure you set "Max segment length for discretized arcs" (Edit -> Preferences -> Import-Export -> SVG) to something like 0.1mm.
 +
* If you use Inkscape to convert SVG to DXF, select DXF R14 and **not** R12. The R12 crashes LaserWorks (it simply closes on import)
  
=== some practical examples: (seperate page?) ===
+
'''Engraving / Raster format''':
these (usefull?) things are what people actually made and hopefully documented it for others to use. (hint hint)
+
* Our current laser cutter has a fixed resolution of 100 DPI.
 +
* [[Ctrl-Cut]] supports automatic conversion to grayscale and stretching the contrast, but if you convert the image to monochrome (1-bit) _before_ importing it won't adjust the image at all, so you can manually tweak it.
  
=== some theoretical/experimental examples: (seperate page?) ===
+
===Repeating Lazzzor Jobs===
this section explores different possibilities of parameters and their outcome.
+
Using [[Ctrl-Cut]] you can save lazzzor cutter jobs with all settings and optimizations applied as .cut file. Next time just open it and press "Send",
this is a good place to get you an idea on how to fine tune your parameters.
 
  
Material:
+
===Color Mapping===
 +
If you use different colors for vectors in your file, [[Ctrl-Cut]] automatically creates different cut items, that you can apply settings to individually.
  
* the material
+
== The Materials ==
** diffrent parameters 1
+
If you want to cut or engrave something, bring your own material, though you can also use any leftovers or stuff which does not have a label on it. (of course labels which say "free for all" are ok, too). Feel free to donate a little extra if you use some materials.
** diffrent parameters 2
 
** diffrent parameters 3
 
  
* soap
+
== Further Reading ==
** engraving a soap ended in the soap swelling. or so ive heard.
+
[[Datei:intro.pdf]]
  
[[Category:Documentation]]
+
[[Kategorie:English]]
[[Category:Lazzzor]]
+
[[Kategorie:Howto]]
[[Category:English]]
+
[[Kategorie:Lazzzor]]

Aktuelle Version vom 12. April 2023, 15:07 Uhr

Language: English

How to Lazzzor or "Why you won't use scissors anymore."

Before you begin you should know..

DO NOT HANDLE THE LAZZZOR IF YOU ARE NOT AUTHORIZED TO.

Only Lazzzorauth key owners are able to operate the mighty Lazzzor. If you are authorized as well because you've successfully completed a Lazzzor_Cutter_Workshop _AND_ you've been given approval by one of the laser admins you may request your own Lazzzorauth iButton.


All others will need a assisting* key owner that is responsible for safe operation.

Amongst others some friendly helpers are:

anlumo, ripper, luto, ...


So, you want to use the mighty fine lazzzor yesyes? Then you will have to complete several trials to step up to the throne of being a lazzzor king or queen.

Basically, you have 2 options:

  • cutting: for this you need a vector graphic,
  • engraving: for this you need a raster image

You can also do both! if you put a rasterized object inside a vector graphic. Alternatively you can create a separate file for each job.

prepare your image

Get your favorite vector/raster drawing program and draw some stuff you want to have cut or engraved. Depending on what you want to do, your image file is qualified for print if the following things apply.

for both: your image/graphic should fit into the workspace which is 1300mmx900mm big. Cutting / Vector format:

  • deactivate filling on all objects
  • set the stroke width on all objects to 0.001 inch (or hairline)

** watch out for duplicated vectors lying on top of each other. it results in the line being cut twice. Ctrl-Cut automatically handles duplicate lines.

  • export your model in pdf format (it is also possible to use ai, ps, eps, ctrl-cut vector format and svg, but pdf is highly recommended).
  • If you use FreeCAD to export SVG, make sure you set "Max segment length for discretized arcs" (Edit -> Preferences -> Import-Export -> SVG) to something like 0.1mm.
  • If you use Inkscape to convert SVG to DXF, select DXF R14 and **not** R12. The R12 crashes LaserWorks (it simply closes on import)

Engraving / Raster format:

  • Our current laser cutter has a fixed resolution of 100 DPI.
  • Ctrl-Cut supports automatic conversion to grayscale and stretching the contrast, but if you convert the image to monochrome (1-bit) _before_ importing it won't adjust the image at all, so you can manually tweak it.

Repeating Lazzzor Jobs

Using Ctrl-Cut you can save lazzzor cutter jobs with all settings and optimizations applied as .cut file. Next time just open it and press "Send",

Color Mapping

If you use different colors for vectors in your file, Ctrl-Cut automatically creates different cut items, that you can apply settings to individually.

The Materials

If you want to cut or engrave something, bring your own material, though you can also use any leftovers or stuff which does not have a label on it. (of course labels which say "free for all" are ok, too). Feel free to donate a little extra if you use some materials.

Further Reading

Datei:Intro.pdf