Laser/Experiments: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(Linking to test file used with parameters)
 
(4 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)
Zeile 14: Zeile 14:
  
 
* Leather
 
* Leather
** Got a 1,5mm raw dark-brown leather, cutting goes incredible good, but on one side it goes better then on the other. Speed: 45, Power: 100, Freq.: 2500
+
** Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500
 
** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
 
** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
  
Zeile 21: Zeile 21:
 
** Power 10%
 
** Power 10%
 
** Pulse frequency 2500Hz
 
** Pulse frequency 2500Hz
 +
* Less thin felt (de: Filz), about 3mm
 +
** Cutting: Speed 90%, Power 20%
 +
** Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense)
 +
 +
* Jeans / Denim
 +
** engraving: 60% speed, 60% power.
 +
** engraving of denim glued onto wood: 60% speed, 100% power gets almost through the cloth and makes the wood partially visible.
 +
** cutting of denim glued onto wood: just cut a bit slower than through the wood alone (e.g. 15% speed instead of 20% speed)
  
 
== ideas ==
 
== ideas ==
 
* making a example raster / vector file for experimental cuts
 
* making a example raster / vector file for experimental cuts
** using color mapping for different speed/power/frequency in one job..
+
** using color mapping for different speed/power/frequency in one job. One example is [[:Datei:slowdowntest.svg]], see also [[Laser/Parameters#Notes on engraving vector lines]].
 +
 
 +
 
 +
== settings for circuit boards ==
 +
* montana black 312g net/11 oz. blue spray paint use speed 50%, power 100% and 5000hz
  
[[Category:Lazzzor]]
+
[[Kategorie:English]]
[[Category:English]]
+
[[Kategorie:Lazzzor]]

Aktuelle Version vom 11. September 2023, 12:07 Uhr

about

This section explores different possibilities of parameters and their outcome. This is a good place to get you an idea on how to fine tune your parameters.

Material:

  • The material
    • different parameters 1
    • different parameters 2
    • different parameters 3
  • Soap
    • engraving a soap ended in the soap swelling, or so I’ve heard.
  • Leather
    • Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500
    • Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
  • Thin felt (knorrprandel Bogen 1mm)
    • Speed 100%
    • Power 10%
    • Pulse frequency 2500Hz
  • Less thin felt (de: Filz), about 3mm
    • Cutting: Speed 90%, Power 20%
    • Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense)
  • Jeans / Denim
    • engraving: 60% speed, 60% power.
    • engraving of denim glued onto wood: 60% speed, 100% power gets almost through the cloth and makes the wood partially visible.
    • cutting of denim glued onto wood: just cut a bit slower than through the wood alone (e.g. 15% speed instead of 20% speed)

ideas


settings for circuit boards

  • montana black 312g net/11 oz. blue spray paint use speed 50%, power 100% and 5000hz