Laser/Experiments: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springenReox (Diskussion | Beiträge) |
Chrysn (Diskussion | Beiträge) (tests for the metalab lazzzor mouzzze pad) |
||
| (6 dazwischenliegende Versionen von 5 Benutzern werden nicht angezeigt) | |||
| Zeile 14: | Zeile 14: | ||
* Leather | * Leather | ||
| − | ** Got a 1,5mm raw dark-brown leather, cutting goes | + | ** Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500 |
** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather | ** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather | ||
| + | |||
| + | * Thin felt ([http://www.creativehobbiesgroup.com/product/8436460 knorrprandel Bogen 1mm]) | ||
| + | ** Speed 100% | ||
| + | ** Power 10% | ||
| + | ** Pulse frequency 2500Hz | ||
| + | * Less thin felt (de: Filz), about 3mm | ||
| + | ** Cutting: Speed 90%, Power 20% | ||
| + | ** Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense) | ||
| + | |||
| + | * Jeans / Denim | ||
| + | ** engraving: 60% speed, 60% power. | ||
| + | ** engraving of denim glued onto wood: 60% speed, 100% power gets almost through the cloth and makes the wood partially visible. | ||
| + | ** cutting of denim glued onto wood: just cut a bit slower than through the wood alone (e.g. 15% speed instead of 20% speed) | ||
== ideas == | == ideas == | ||
| Zeile 22: | Zeile 35: | ||
| − | [[ | + | == settings for circuit boards == |
| − | [[ | + | * montana black 312g net/11 oz. blue spray paint use speed 50%, power 100% and 5000hz |
| − | + | ||
| + | [[Kategorie:English]] | ||
| + | [[Kategorie:Lazzzor]] | ||
Version vom 12. März 2019, 20:20 Uhr
about
This section explores different possibilities of parameters and their outcome. This is a good place to get you an idea on how to fine tune your parameters.
Material:
- The material
- different parameters 1
- different parameters 2
- different parameters 3
- Soap
- engraving a soap ended in the soap swelling, or so I’ve heard.
- Leather
- Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500
- Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
- Thin felt (knorrprandel Bogen 1mm)
- Speed 100%
- Power 10%
- Pulse frequency 2500Hz
- Less thin felt (de: Filz), about 3mm
- Cutting: Speed 90%, Power 20%
- Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense)
- Jeans / Denim
- engraving: 60% speed, 60% power.
- engraving of denim glued onto wood: 60% speed, 100% power gets almost through the cloth and makes the wood partially visible.
- cutting of denim glued onto wood: just cut a bit slower than through the wood alone (e.g. 15% speed instead of 20% speed)
ideas
- making a example raster / vector file for experimental cuts
- using color mapping for different speed/power/frequency in one job..
settings for circuit boards
- montana black 312g net/11 oz. blue spray paint use speed 50%, power 100% and 5000hz
