Laser/Experiments: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(→‎about: added leather, new material)
(5 dazwischenliegende Versionen von 4 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
 
 
== about ==
 
== about ==
 
This section explores different possibilities of parameters and their outcome.
 
This section explores different possibilities of parameters and their outcome.
Zeile 15: Zeile 14:
  
 
* Leather
 
* Leather
** Got a 1,5mm raw dark-brown leather, cutting goes incredible good, but on one side it goes better then on the other. Speed: 100, Power: 60, Frequency:500Hz
+
** Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500
 
** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
 
** Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
 +
 +
* Thin felt ([http://www.creativehobbiesgroup.com/product/8436460 knorrprandel Bogen 1mm])
 +
** Speed 100%
 +
** Power 10%
 +
** Pulse frequency 2500Hz
 +
* Less thin felt (de: Filz), about 3mm
 +
** Cutting: Speed 90%, Power 20%
 +
** Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense)
  
 
== ideas ==
 
== ideas ==
Zeile 22: Zeile 29:
 
** using color mapping for different speed/power/frequency in one job..
 
** using color mapping for different speed/power/frequency in one job..
  
 
+
[[Kategorie:English]]
[[Category:Dokumentation]]
+
[[Kategorie:Lazzzor]]
[[Category:Lazzzor]]
 
[[Category:English]]
 

Version vom 28. Dezember 2015, 11:44 Uhr

about

This section explores different possibilities of parameters and their outcome. This is a good place to get you an idea on how to fine tune your parameters.

Material:

  • The material
    • different parameters 1
    • different parameters 2
    • different parameters 3
  • Soap
    • engraving a soap ended in the soap swelling, or so I’ve heard.
  • Leather
    • Got a 1,5mm raw dark-brown leather, cutting goes incredibly well, but on one side it goes better then on the other. Speed: 45 or 40, Power: 100, Freq.: 2500
    • Engraving is not soo good, you can see the engraved parts, but only on 100/100, and then its not even black or something... May this depends on your leather
  • Thin felt (knorrprandel Bogen 1mm)
    • Speed 100%
    • Power 10%
    • Pulse frequency 2500Hz
  • Less thin felt (de: Filz), about 3mm
    • Cutting: Speed 90%, Power 20%
    • Engraving: more experiments to be done, but note: large black areas will melt the material deeply, thin lines will result in very betauful printing on the material (I used red felt, engraving on dark/brown/black felt might not make much sense)

ideas

  • making a example raster / vector file for experimental cuts
    • using color mapping for different speed/power/frequency in one job..