GoCNC: Unterschied zwischen den Versionen

aus Metalab, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Wechseln zu: Navigation, Suche
(Tech Specs)
(2 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt)
Zeile 2: Zeile 2:
 
{{Languages|en}}
 
{{Languages|en}}
 
{{Machine
 
{{Machine
 +
|image=GoCNC A4Advanced.jpg
 
|owner=Metalab
 
|owner=Metalab
 
|status=Aktiv
 
|status=Aktiv
 
|requirestraining=more or less
 
|requirestraining=more or less
 
|requiresauth=NOPE
 
|requiresauth=NOPE
|cost=500€
+
|cost=900€
 
|teachers=contact cnc@lists.metalab.at
 
|teachers=contact cnc@lists.metalab.at
 
}}
 
}}
  
GoCNC is a small [[CNC-Fräse]] machine for milling in max A4 size.
+
GoCNC is a small [[CNC-Fräse]] machine for milling in max A4 size. <br /><small>It was [http://geilomat.soup.io/post/357365039/Thank-you-Christoph-S-for-donating-a donated by Christoph S.] in Oct. 2013.</small>
  
 
== Tech Specs ==
 
== Tech Specs ==
  
 +
* [http://gocnc.de/product_info.php?cPath=22&products_id=32&language=en&osCsid=0dccfe57673957c911a8047a827c84dd CNC Milling machine GoCNC Hobby A4 Advanced]
 
* Steppers are set to 1.5A, 8 Microsteps
 
* Steppers are set to 1.5A, 8 Microsteps
 
** It uses a Stepp2500a control board
 
** It uses a Stepp2500a control board
Zeile 20: Zeile 22:
 
* Maximum Speed: around 1000mm/min
 
* Maximum Speed: around 1000mm/min
 
* For use with Dremel or Proxxon Device as spindle
 
* For use with Dremel or Proxxon Device as spindle
* It uses M10 threaded rods, which are quite bad...  
+
* It uses M10 threaded rods, which are quite bad...
 +
* You can not put too much torque on the screws that hold the Z axis on the X axis - therefore the axis is not very stable.
 +
** If you fix the axis, the axis will be locked!
  
 
== Configuration ==
 
== Configuration ==
Zeile 31: Zeile 35:
 
== Profit ==
 
== Profit ==
  
It Plays Tetris!
+
It plays Tetris!
  
 
{{#ev:youtube|4MelMEhzIfM}}
 
{{#ev:youtube|4MelMEhzIfM}}
  
 
(just to give you one example ;))
 
(just to give you one example ;))
 +
 +
== Maybe Updates ==
 +
 +
* Break out the Relais for the spindle, maybe  little bit tricky because the control board is not very well fixated inside the box
 +
* Use connectors instead of soldering - same problem as with the geilomat
 +
* fix cable lengths because complete area cannot be reached
 +
* use a silent fan
  
 
[[Kategorie:Maschinen]]
 
[[Kategorie:Maschinen]]

Version vom 4. November 2013, 01:03 Uhr

Language: English


GoCNC
GoCNC A4Advanced.jpg

Eigentümer:

Metalab

Status:

Aktiv

Erfordert Einschulung:

more or less

Erfordert Authentisierung:

NOPE

Kostet:

900€

Hilfsbereite:

contact cnc@lists.metalab.at


GoCNC is a small CNC-Fräse machine for milling in max A4 size.
It was donated by Christoph S. in Oct. 2013.

Tech Specs

  • CNC Milling machine GoCNC Hobby A4 Advanced
  • Steppers are set to 1.5A, 8 Microsteps
    • It uses a Stepp2500a control board
    • Steppers are Nanotec ST5918X1008-B 4.9V 1.0A
  • Maximum working Plane: X165, Y290, Z65
  • Maximum Speed: around 1000mm/min
  • For use with Dremel or Proxxon Device as spindle
  • It uses M10 threaded rods, which are quite bad...
  • You can not put too much torque on the screws that hold the Z axis on the X axis - therefore the axis is not very stable.
    • If you fix the axis, the axis will be locked!

Configuration

Currently the mill is working with the LinuxCNC Setup on the CNC PC. There is an option for a USB Device that does the realtime stuff in a FPGA but that only works with a Windows PC.

If you are familiar with the LinuxCNC Workflow on the Geil-o-Mat, you can use it as well as on the GoCNC with the difference that the Spindle is NOT automatically turned on and off because the Relais on the control board can not be attached to the spindle!!!

Profit

It plays Tetris!

(just to give you one example ;))

Maybe Updates

  • Break out the Relais for the spindle, maybe little bit tricky because the control board is not very well fixated inside the box
  • Use connectors instead of soldering - same problem as with the geilomat
  • fix cable lengths because complete area cannot be reached
  • use a silent fan