Blinkenpoi: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
 
Zeile 90: Zeile 90:
 
When we reach the end of the file we just set the filedescriptor to seek(0) and start over.
 
When we reach the end of the file we just set the filedescriptor to seek(0) and start over.
  
 +
== User contributed Usage guid ==
  
 +
pink: colour after starting the poi - press button now to ovverride the network setup - longpress leads to NETWORK RESET and 3x red blinking
  
 +
white: connecting with previously configured network
  
==TODOs==
+
green: connected with configured network
The Webinterface is 95% done.
 
  
It works, but it needs some love especially warnings and feedback if you are about to delete or overwrite something.
+
yellow: Open Access Point on Blinkenpoi for setup
  
This functionality needs to be implemented in Javascript / jQuery
+
  
We need to add a fat Capacitor on the PCB
+
Reset Wifi-Setup:
  
We could add a second button
+
After starting, when LED is pink, press and hold the reset-button. Then the LED should flash red three times.
  
Maybe migrate everything to an ESP32 and port the firmware to MicroPython. ESP8266 is not sufficient for this Project + MicroPython
+
 +
 
 +
Connect Poi to your Wifi:
 +
 
 +
Connect the Poi via USB to your Computer.
 +
Search for Blinkenpoi in the accessable networks.
 +
Connect to it.
 +
A captive portal is opened (browser popup).
 +
If it does not open automatically open a browser and go to [http://192.168.4.1]
 +
Choose Wifi-Setup in the menu and choose your wifi (for example the Hotspot of your Smartphone), enter the password and click "Save".
 +
The poi should turn from yellow to green after a couple of seconds and turn dark on successful pairing to the hotspot.
 +
 
 +
Now, when you start the poi, the LED first flashes pink, then white and finally green and turns off again.
 +
In your Wifi-Device/Smartphone open the Browser and enter blinkenpoi.local.
 +
If your device does not support MDMS - which is the case for android - you have to enter the IP-Adress of your Poi.
 +
If you don't know its IP address you can use nmap, look on the router or attach a usb cable and take a look on the terminal provided by the blinkenpoi.
 +
for example '''screen /dev/tty.usbserial0 115200'''
 +
or you could connect another computer that can resolve nDNS to your hostpot and open http://blinkenpoi.local in the browser
  
  

Aktuelle Version vom 30. Dezember 2019, 22:06 Uhr

Blinkenpoi
Blinkenpoi.jpg
Gestartet: 16.7.2019
Involvierte: overflo
Status: in progress
Beschreibung: poi with leds
Shutdownprozedur:
Zuletzt aktualisiert: 2019-12-30


Momentaufnahme
Noch eine Momentaufnahme
Kurz darauf
Animationen aussuchen / abspielen / synchronisieren
Animationseditor / Upload

Blinkenpoi

  • ESP8266 (WeMos D1 Mini)
  • Custom PCB with 2 buttons (1 working)
  • Waterjet cutted Polycarbonate body
  • 50 APA102 Leds
  • Battery holder for 3xAAA
  • Transparent rubber tube
  • Fingerloops / Attachments


Trivia

I started Blinkenpoi ~10 years ago and respawned that project 6 Weeks before CCCamp19 with a new Microcontroller, a Webinterface and modern Ledstrips.

The Webinterface has some cool features like "Local scan" to find other Blinkenpois automatically when they are connected to the same hotspot / mobile access point.

You can synchronize the playback on multiple devices, you can create, upload, download and share Animations directly in the Webinterface.

The Blinkenpoi opens its own Accesspoint for wireless setup and features:

  • Local storage of wlan credentials
  • Auto connect once configured
  • Reset of configuration
  • Verbose Debug Interface over usb->serial
  • 3Mb storage for custom animations
  • Firmware written in C++ (Arduino Framework)
  • 100% Open Source Public Domain / Do whatever you want

Usage

Whenever you turn on a Blinkenpoi, the first led will shine in bright pink.

You have 2 seconds to press the button and override network setup while the led is pink.

If you override the setup the first available animation is loaded.

You can cycle trough all available animations with the button till the Blinkenpoi turns dark again.

If you press the button again the first animation is loaded again.

If you press the button for 2 seconds or longer the first led will flash red 3 times and the local config is erased.

All credentials and configurations are purged and it will open an Accesspoint on reboot for configuration.

When you turn on the Blinkenpoi for the first time, it opens an Accesspoint called "Blinkenpoi".

Once connected to it, you will be greeted by a captive portal / WLAN setup screen where you enter the credentials of the WLAN your Blinkenpoi should connect to and a name for the Blinkenpoi.

The led will turn from yellow to green and then dark if the Blinkenpoi connected successfully.

The Blinkenpoi is now connected and can be reached at http://blinkenpoi.local from a machine connected to the same network.

There is a webinterface for configuration, network scanning, animation playback and animation creation available directly on the Blinkenpoi.


Assembly Instructions

Video: Handstrap

Video: Blinkenpoi assembly


Animation format

The Animations are saved on the Blinkenpoi in a raw format.

Each Pixel has 3 Bytes for RGB, There are 50 Pixels, but only 25 on each Side.

We save 25*3 Bytes / Column and simply read the bytes back from the file and set the RGB values from that data.

No headers. no metadata, but super fast.

When we reach the end of the file we just set the filedescriptor to seek(0) and start over.

User contributed Usage guid

pink: colour after starting the poi - press button now to ovverride the network setup - longpress leads to NETWORK RESET and 3x red blinking

white: connecting with previously configured network

green: connected with configured network

yellow: Open Access Point on Blinkenpoi for setup


Reset Wifi-Setup:

After starting, when LED is pink, press and hold the reset-button. Then the LED should flash red three times.


Connect Poi to your Wifi:

Connect the Poi via USB to your Computer. Search for Blinkenpoi in the accessable networks. Connect to it. A captive portal is opened (browser popup). If it does not open automatically open a browser and go to [1] Choose Wifi-Setup in the menu and choose your wifi (for example the Hotspot of your Smartphone), enter the password and click "Save". The poi should turn from yellow to green after a couple of seconds and turn dark on successful pairing to the hotspot.

Now, when you start the poi, the LED first flashes pink, then white and finally green and turns off again. In your Wifi-Device/Smartphone open the Browser and enter blinkenpoi.local. If your device does not support MDMS - which is the case for android - you have to enter the IP-Adress of your Poi. If you don't know its IP address you can use nmap, look on the router or attach a usb cable and take a look on the terminal provided by the blinkenpoi. for example screen /dev/tty.usbserial0 115200 or you could connect another computer that can resolve nDNS to your hostpot and open http://blinkenpoi.local in the browser


Series of Tubes

GITHUB repo