Bandsaw: Unterschied zwischen den Versionen

aus Metalab, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Wechseln zu: Navigation, Suche
(Die Seite wurde neu angelegt: „The Metalab currently has 3 different Bandsaws. A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines. ==…“)
 
Zeile 1: Zeile 1:
The Metalab currently has 3 different Bandsaws.
+
The Metalab currently has 3 different Bandsaws. Two Bandsaws are from Joe since [[2014-05-01_Jour_Fixe]].
  
 
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
 
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
 +
 +
== Current Status ==
 +
 +
* Green Saw (Joe): Band is broken, otherwise useable
 +
* Blue Saw (Joe): Operational, but band is a little bit rusty
 +
* Blue Saw (Metalab): Upper and Lower Band holder is broken - not useable at all
  
 
== How to Operate ==
 
== How to Operate ==
 +
 +
* Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!)
 +
** See Repair Guide otherwise...
 +
* Check if the band is OK
 +
** See Repair Guide otherwise..
 +
* Adjust the upper band holder to the correct hight (It should be right about your workpiece)
 +
* Switch it on
 +
* Saw
 +
 +
=== General Tips ===
 +
 +
* Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside
 +
* A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine
 +
* The band swings in every direction a few parts of a mm. Consider that while you are sawing!
  
 
== How to Repair ==
 
== How to Repair ==
 +
 +
There is a good guide how to correctly setup a bandsaw here: [http://www.1-2-do.com/forum/bandsaege-richtig-einstellen-thema-14087.html Bandsäge einstellen (German)]

Version vom 10. Juni 2014, 11:31 Uhr

The Metalab currently has 3 different Bandsaws. Two Bandsaws are from Joe since 2014-05-01_Jour_Fixe.

A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.

Current Status

  • Green Saw (Joe): Band is broken, otherwise useable
  • Blue Saw (Joe): Operational, but band is a little bit rusty
  • Blue Saw (Metalab): Upper and Lower Band holder is broken - not useable at all

How to Operate

  • Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!)
    • See Repair Guide otherwise...
  • Check if the band is OK
    • See Repair Guide otherwise..
  • Adjust the upper band holder to the correct hight (It should be right about your workpiece)
  • Switch it on
  • Saw

General Tips

  • Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside
  • A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine
  • The band swings in every direction a few parts of a mm. Consider that while you are sawing!

How to Repair

There is a good guide how to correctly setup a bandsaw here: Bandsäge einstellen (German)