Bandsaw: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(remove old saw)
 
(16 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 1: Zeile 1:
The Metalab currently has 3 different Bandsaws. Two Bandsaws are from Joe since [[2014-05-01_Jour_Fixe]].
+
The Bandsaws are owned by Joe and where in the lab since [[2014-05-01_Jour_Fixe]] but was removed in Feb 2016.
  
 
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
 
A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.
Zeile 5: Zeile 5:
 
== Current Status ==
 
== Current Status ==
  
* Green Saw (Joe): Band is broken, otherwise useable
+
* Bergin / Clarke CBS 355: 1780mm +-3mm x 6mm, 6 TPI
* Blue Saw (Joe): Operational, but band is a little bit rusty
+
* '''NOT''' in working condition
* Blue Saw (Metalab): Upper and Lower Band holder is broken - not useable at all
+
** See https://lists.metalab.at/pipermail/cnc/2014-May/000903.html
 +
** http://www.clarkeservice.co.uk/manuals/woodworker/cbs355.pdf
  
 
== How to Operate ==
 
== How to Operate ==
Zeile 18: Zeile 19:
 
* Switch it on
 
* Switch it on
 
* Saw
 
* Saw
 +
 +
{{#ev:youtube|MBbFBf5t0Kk|320}}
  
 
=== General Tips ===
 
=== General Tips ===
Zeile 28: Zeile 31:
  
 
There is a good guide how to correctly setup a bandsaw here: [http://www.1-2-do.com/forum/bandsaege-richtig-einstellen-thema-14087.html Bandsäge einstellen (German)]
 
There is a good guide how to correctly setup a bandsaw here: [http://www.1-2-do.com/forum/bandsaege-richtig-einstellen-thema-14087.html Bandsäge einstellen (German)]
 +
 +
Blades:
 +
* http://www.hisi.at/produkte/sagebander/bimetall-sagebander/
 +
* http://www.ibh-werkzeuge.at/IBH/Holz_%26_Kunststoff.html
 +
* http://www.albinkraus.at/en/1892520/Woodworking-Cutting-tools.html
 +
* http://www.harton.co.at/index.aspx?show=schaerfdienst

Aktuelle Version vom 27. August 2017, 19:43 Uhr

The Bandsaws are owned by Joe and where in the lab since 2014-05-01_Jour_Fixe but was removed in Feb 2016.

A bandsaw can be used to cut wood, metalls and plastics not only in straight lines, but also curved lines.

Current Status

How to Operate

  • Check if band is correctly tightned (Do it with caution, because the band is very sharp and can easily injure you!)
    • See Repair Guide otherwise...
  • Check if the band is OK
    • See Repair Guide otherwise..
  • Adjust the upper band holder to the correct hight (It should be right about your workpiece)
  • Switch it on
  • Saw

General Tips

  • Do not use the bedstop (Seitenanschlag), because the cut off piece can easily lock up there and press the band aside
  • A Bandsaw is a free-hand tool, mark you cut path and cut there instead of measuring on the machine
  • The band swings in every direction a few parts of a mm. Consider that while you are sawing!

How to Repair

There is a good guide how to correctly setup a bandsaw here: Bandsäge einstellen (German)

Blades: