Dome: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen| Zeile 4: | Zeile 4: | ||
[[Datei:dome_build.jpg|200px|thumb|right|Construction]] | [[Datei:dome_build.jpg|200px|thumb|right|Construction]] | ||
| + | [[Datei:dome_done.jpg|200px|thumb|right|Done!]] | ||
[[Datei:dome_kuschelig.jpg|200px|thumb|right|Cosy]] | [[Datei:dome_kuschelig.jpg|200px|thumb|right|Cosy]] | ||
[[Datei:dome_down.jpg|200px|thumb|right|Deconstruction (~10 minute with 5 guys)]] | [[Datei:dome_down.jpg|200px|thumb|right|Deconstruction (~10 minute with 5 guys)]] | ||
| Zeile 87: | Zeile 88: | ||
[http://www.domerama.com/calculators/4v-geodesic-dome-calculator/ DOMERAMA online dome calculator] | [http://www.domerama.com/calculators/4v-geodesic-dome-calculator/ DOMERAMA online dome calculator] | ||
| + | [http://stadtflucht.soup.io/ Many pix in soup] | ||
== TODO== | == TODO== | ||
| − | + | * measure the sizes of the different triangles / create different inlays with mirors and out of acrylic | |
| − | + | * measure the top / center pentagon for replacement with solid wood | |
| − | + | * add sprinklers for water | |
| − | + | * add ventilator | |
| − | + | * add 71 leds | |
| − | + | * make ledmount | |
| − | |||
| − | |||
| − | |||
| − | |||
Version vom 19. Juli 2015, 21:45 Uhr
MIDDLE - LEFT - RIGHT
You need:
- 250 bars (get 270+ to have some spareparts) the inner parts of slatted frames for beds work great
- 91 M6 screws (length: 80 mm)
- 91 Wing nuts
- 182 Washers (the bigger the better)
- Spray paint (RED,GREEN,BLUE,ORANGE)
Cut them in 5 different lengths.
| Type | Color | Pcs. | Length |
| A | ORANGE | 30 | 60cm |
| B | RAINBOW | 90 | 70cm |
| D | GREEN | 70 | 74.2cm |
| E | BLUE | 30 | 77cm |
| F | RED | 30 | 70.8cm |
Drill a hole 2cm from the border in the middle of the struts ends.
Assembly
Start with 5 pcs type A struts (orange) Connect them like this: WASHER, SCREW, 5 BARS (A),WASHER,WING NUT, dont over tighten yet
You successfully put together the middle structure that will be on the center top of the dome.
Now from the end of these connect 5 type B struts. The magic formular is:
MIDDLE - LEFT - RIGHT
- MIDDLE (A) outermost
- LEFT (B) middle
- RIGHT(B) innermost layer
and thats how you go on according to the diagram above.
This is true for the whole assembly.
Take a corner of a triangle, consider that "middle" and connect left and right to it.
Links
DOMERAMA online dome calculator
TODO
- measure the sizes of the different triangles / create different inlays with mirors and out of acrylic
- measure the top / center pentagon for replacement with solid wood
- add sprinklers for water
- add ventilator
- add 71 leds
- make ledmount
