Mendel90: Unterschied zwischen den Versionen

(27 dazwischenliegende Versionen von 7 Benutzern werden nicht angezeigt)

Zeile 3:

|image=m90.png

|owner=Metalab

|status=~~Aktiv~~

|status=zerlegt

|requirestraining=Ja

|requiresauth=Ja

|cost=660EUR

|teachers=prikle

|teachers=[[User:prikle|prikle]],[[User:Hetti|Hetti]]

}}

*Location: [[~~Scannerraum~~]]

Location: [[WhateverLab]]

*Soup: http://reprap.soup.io/

Soup: http://reprap.soup.io/

*Mailinglist https://lists.metalab.at/mailman/listinfo/3d-printing

Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing

~~=== The Model~~: ~~Mendel90 ===~~

'''Handbuch für unseren 3Dprinter:''' [[/3DPrinter-Manual]]

* Model Homepage: http://reprap.org/wiki/Mendel90

* Assembly Instruction/Doku: https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf

* Blog of Creator: http://hydraraptor.blogspot.com/

* THE SOURCE: https://github.com/nophead/Mendel90

* Order Detail: http://forums.reprap.org/read.php?94,196585

* If you are bored and want to see a complete build from zero to hero (from buildscript to finished printer) in less than two hours (including software setup; note that we will order the kit from the designer so we don'~~t need half of the steps): https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z~~

* Latest maintenance:

** (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[~~Datei:Marlin~~-~~140830a.zip~~]]

*** Support for arcs, doesn't accelerate/decelerate for polygons

*** Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features

= Software / prerequisites =

[http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver]

[http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])

[http://slic3r.org/ Slic3r]

= Resources =

Slic3r Config Bundle for Mendel90 and Witbox: [[Datei:Slic3r_config_bundle_metalab_v1.zip]]

Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]

Settings for Slic3r (Octoprint): [[Datei:Mendel90_Octoprint_v2.ini.zip]]

Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]

= About the Mendel90 =

[http://reprap.org/wiki/Mendel90 Mendel page] on reprap.org

[https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf Assembly instructions/documentation] (pdf)

Creator's own [http://hydraraptor.blogspot.com/ blog]

[https://github.com/nophead/Mendel90 Code source]

[http://forums.reprap.org/read.php?94,196585 Ordering a Mendel90 Kit]

[https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z Video] of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.

Latest maintenance:

* (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip]]

* Support for arcs, doesn't accelerate/decelerate for polygons

* Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features

~~{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}~~

~~=== Resources ===~~

* Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]

* Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]

Finances Required to buy the printer:

Zeile 40:

Zeile 55:

* '''Total: 660 EUR''' (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))

== 3D Printer Workshop ==

= 3D Printer Workshop =

Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen.

Bei bedarf bitte bei [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.

Bei bedarf bitte bei [[Benutzer:MiKa|MiKa]] oder [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.

===Nächster Workshop:===

== Nächster Workshop:==

* Mi '''10.09.2014''' in der [[Bibliothek]] um 19Uhr

Zeile 55:

Zeile 70:

# [[User:metaz|meta]]

# [[User:A|A]]

# [[User:jk|Jozef]]

# [[User:You|You?]]

== Supporters - Mendel 90: ==

= Supporters - Mendel 90: =

{| class="wikitable"