HSC2011/Enclosure: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen (Die Seite wurde neu angelegt: „== Enclosure == in here we need: * screenshots from blender * photos of the final enclosure * .stl files for 3d rpinting * . svg .cdr .ai files for the lazzzored…“) |
Mazzo (Diskussion | Beiträge) |
||
| (7 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| − | + | <small>< [[HSC2011]]</small> | |
| − | in here | + | __TOC__ |
| − | * screenshots from | + | |
| − | + | == About the enclosure == | |
| − | + | The enclosure was designed and manufactured by [[Benutzer:Mazzo| mazzo]] using Blender and our makerbot "le giraffe" | |
| − | + | ||
| + | == Files needed for the production of the enclosure == | ||
| + | |||
| + | * All up to date files are found in the [https://github.com/Metalab/hsc2011/enclosure/ GIT repository] here is short summary of the important files | ||
| + | ** [[:Datei:Edubuzzer_stl_gcode.zip | Gcode and STL files]] to feed your 3D printer omnomnomnom | ||
| + | ** [[:Datei:edubuzzer_middlepart.cdr | The middlepart for the lazzor]] You should cut this from 6mm acryl | ||
| + | ** [[:Datei:EduBuZZer_Final.blend | Blender file ]] | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | == Some screenshots from Blender == | ||
| + | {| | ||
| + | ! width="450"| | ||
| + | ! width="450"| | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:eb_bottom.png|thumb|400px|left|The bottom of the EduBuzzer enclosure]] | ||
| + | | valign="top"|[[Bild:eb_top.png|thumb|400px|left|The top of the EduBuzzer enclosure]] | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:eb_complete_black.png|thumb|400px|left|The complete EduBuzzer enclosure]] | ||
| + | | valign="top"|[[Bild:eb_complete.png|thumb|400px|left|Highlighted Battery holder, on/off switch holder and PCB]] | ||
| + | |||
| + | |} | ||
| + | |||
| + | |||
| + | == Photos of the final enclosure == | ||
| + | {| | ||
| + | ! width="450"| | ||
| + | ! width="450"| | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:Enclosure_and_pcb.JPG|thumb|400px|left|The enclosure + PCB]] | ||
| + | | valign="top"|[[Bild:Enclosure_bottom.JPG|thumb|400px|left|The bottom half of the enclosure]] | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:Enclosure_full_assembled.JPG|thumb|400px|left|Fully assembled!]] | ||
| + | | valign="top"|[[Bild:Enclosure_middlepart.JPG|thumb|400px|left|The middlepart is lazzored and the RGB led shines in there to change the color of the enclosure]] | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:Enclosure_middlepart_assy.JPG|thumb|400px|left|middlepart attched to the enclosure]] | ||
| + | | valign="top"|[[Bild:Enclosure_pcb_off.JPG|thumb|400px|left|connection on the bottom for the iButton, on/off switch + power]] | ||
| + | |||
| + | |- | ||
| + | | valign="top"|[[Bild:Enclosure_rgb_inlay.JPG|thumb|400px|left|bottompart + middlepart + pcb ]] | ||
| + | |} | ||
| + | |||
| + | ==Blender Animation of the enclosure== | ||
| + | |||
| + | {{#ev:youtube|i9sB169s1X8}} | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | [[Kategorie:HSC2011]] | ||
| + | [[Kategorie:English]] | ||
Aktuelle Version vom 4. Mai 2011, 04:47 Uhr
< HSC2011
About the enclosure
The enclosure was designed and manufactured by mazzo using Blender and our makerbot "le giraffe"
Files needed for the production of the enclosure
- All up to date files are found in the GIT repository here is short summary of the important files
- Gcode and STL files to feed your 3D printer omnomnomnom
- The middlepart for the lazzor You should cut this from 6mm acryl
- Blender file
Some screenshots from Blender
