Umbrella: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen (added troubleshoot for lightswitch) |
(spell check) |
||
| Zeile 2: | Zeile 2: | ||
[[Datei:u_blue.jpg|miniatur]] | [[Datei:u_blue.jpg|miniatur]] | ||
[[Datei:u_pink.jpg|miniatur]] | [[Datei:u_pink.jpg|miniatur]] | ||
| − | + | ||
| − | + | ||
| − | ==How to simply turn on the | + | ==How to simply turn on the light== |
Use the light switch next to the kitchen. You can dim the light with the rotary knob on the side. | Use the light switch next to the kitchen. You can dim the light with the rotary knob on the side. | ||
| − | + | ||
| − | + | ||
[[Datei:Umbrella_lightswitch_1.jpg|200px]] | [[Datei:Umbrella_lightswitch_1.jpg|200px]] | ||
[[Datei:Umbrella_lightswitch_2.jpg|200px]] | [[Datei:Umbrella_lightswitch_2.jpg|200px]] | ||
| + | |||
| + | If it does not work try unplugging and replugging it. Wait a couple of seconds. | ||
| − | |||
==Why== | ==Why== | ||
| − | + | ||
| − | The | + | The Metalab needs some new lights. |
| − | + | ||
ART-net is awesome. | ART-net is awesome. | ||
| − | + | ||
| − | + | ||
== How == | == How == | ||
| − | + | ||
Raspberry Pi 3 + Touchscreen | Raspberry Pi 3 + Touchscreen | ||
| − | + | ||
Distro based on the QLC+ image (raspbian jessie) | Distro based on the QLC+ image (raspbian jessie) | ||
| − | + | ||
| − | QLC+ | + | QLC+ XServer less build that renders directly in GL buffers for performance |
| − | + | ||
H801 based clients (ESP8266) | H801 based clients (ESP8266) | ||
| − | + | ||
Arduino based firmware that implements ART-net | Arduino based firmware that implements ART-net | ||
| − | + | ||
| − | |||
== Temporary setup with QLC+ == | == Temporary setup with QLC+ == | ||
| − | + | ||
Connect to "metalights" WLAN | Connect to "metalights" WLAN | ||
| − | + | ||
Set OUTPUT to 10.20.255.255 | Set OUTPUT to 10.20.255.255 | ||
| − | + | ||
Set ARTnet universe to 3 | Set ARTnet universe to 3 | ||
| − | + | ||
There are 5 channels / Umbrella | There are 5 channels / Umbrella | ||
| − | + | ||
R,G,B,WW,CW | R,G,B,WW,CW | ||
| − | + | ||
| − | If CW or WW are anything else but "0" R,G and B are disabled by firmware | + | If CW or WW are anything else but "0" then R,G and B are disabled by firmware. |
| − | + | ||
| − | If R,G or B are anything but "0" CW and WW are disabled by firmware | + | If R,G or B are anything but "0" then CW and WW are disabled by firmware. |
| − | + | ||
This is to save our power supplies from sudden heat death. | This is to save our power supplies from sudden heat death. | ||
(105 watt / Umbrella max) | (105 watt / Umbrella max) | ||
| − | + | ||
| − | + | ||
== Hardware == | == Hardware == | ||
| − | + | ||
| − | H801 | + | H801 LED controller features: |
| − | + | ||
* 8 Mbit Storage (1 Mb) | * 8 Mbit Storage (1 Mb) | ||
* 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel) | * 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel) | ||
| − | + | ||
| − | + | ||
=== How to flash === | === How to flash === | ||
* Install Arduino 1.6.4 | * Install Arduino 1.6.4 | ||
| Zeile 74: | Zeile 74: | ||
** CPU Frequency: 80 Mhz | ** CPU Frequency: 80 Mhz | ||
** Upload Speed: 115200 or more | ** Upload Speed: 115200 or more | ||
| − | + | ||
| − | + | ||
| − | * Set JUMPER on board to boot into | + | * Set JUMPER on board to boot into flash mode. |
| − | * Power the board | + | * Power up the board. |
| − | + | ||
==Who== | ==Who== | ||
| − | + | ||
| − | Originally invented and built by [[Benutzer:overflo|overflo]], the umbrellas were built by a lot of people | + | Originally invented and built by [[Benutzer:overflo|overflo]], the umbrellas were built by a lot of people in some night shifts at Metalab |
| − | + | ||
| − | LOTS OF SUPPORT BY | + | LOTS OF SUPPORT BY |
uniq, anlumo, ripper, bogdan <your name here> | uniq, anlumo, ripper, bogdan <your name here> | ||
| − | + | ||
==Links== | ==Links== | ||
| − | + | ||
| − | |||
[http://www.qlcplus.org/ QLC+] | [http://www.qlcplus.org/ QLC+] | ||
| − | + | ||
[https://de.aliexpress.com/item/DC5-24V-Wireless-Smart-Dimmer-Receiver-Output-5-Routes-PWM-Data-WiFi-APP-Controlled-for-RGBW H801 Controllers] | [https://de.aliexpress.com/item/DC5-24V-Wireless-Smart-Dimmer-Receiver-Output-5-Routes-PWM-Data-WiFi-APP-Controlled-for-RGBW H801 Controllers] | ||
| − | + | ||
[https://github.com/overflo23/H801_ARTnet Github] | [https://github.com/overflo23/H801_ARTnet Github] | ||
| − | + | ||
[http://www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf ART-net Reference] | [http://www.artisticlicence.com/WebSiteMaster/User%20Guides/art-net.pdf ART-net Reference] | ||
| − | + | ||
[[Artnet]] | [[Artnet]] | ||
Version vom 20. Mai 2017, 19:41 Uhr
How to simply turn on the light
Use the light switch next to the kitchen. You can dim the light with the rotary knob on the side.
If it does not work try unplugging and replugging it. Wait a couple of seconds.
Why
The Metalab needs some new lights.
ART-net is awesome.
How
Raspberry Pi 3 + Touchscreen
Distro based on the QLC+ image (raspbian jessie)
QLC+ XServer less build that renders directly in GL buffers for performance
H801 based clients (ESP8266)
Arduino based firmware that implements ART-net
Temporary setup with QLC+
Connect to "metalights" WLAN
Set OUTPUT to 10.20.255.255
Set ARTnet universe to 3
There are 5 channels / Umbrella
R,G,B,WW,CW
If CW or WW are anything else but "0" then R,G and B are disabled by firmware.
If R,G or B are anything but "0" then CW and WW are disabled by firmware.
This is to save our power supplies from sudden heat death.
(105 watt / Umbrella max)
Hardware
H801 LED controller features:
- 8 Mbit Storage (1 Mb)
- 5 channels each 45 watt max (~ 3.5 Ampere @ 12 V / channel)
How to flash
- Install Arduino 1.6.4
- Install ESP 8266 extensions
- Select Tools:
- GENERIC ESP8266 Module
- Flash Mode: DIO
- Flash Size: 1M (512K SPIFFS)
- Debug Port: Disabled
- Debug Level: none
- Reset Mode: ck
- Flash Frequency: 40 Mhz
- CPU Frequency: 80 Mhz
- Upload Speed: 115200 or more
- Set JUMPER on board to boot into flash mode.
- Power up the board.
Who
Originally invented and built by overflo, the umbrellas were built by a lot of people in some night shifts at Metalab
LOTS OF SUPPORT BY uniq, anlumo, ripper, bogdan <your name here>
