Witbox: Unterschied zwischen den Versionen
Keine Bearbeitungszusammenfassung |
Keine Bearbeitungszusammenfassung |
||
| Zeile 10: | Zeile 10: | ||
}} | }} | ||
__TOC__ | __TOC__ | ||
'''It is OK to use the printer as it is.''' | |||
'''It is NOT OK to modify it in any way.''' | |||
This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap. | |||
===Overview=== | ===Overview=== | ||
| Zeile 23: | Zeile 33: | ||
===How to use it=== | ===How to use it=== | ||
Calibration | Calibration (before every job @ metalab) | ||
Load / Change Filament if neccessary - Careful not to entangle the filament!! | |||
Save your .gcode to the SD card | |||
Start job from menu. | |||
| Zeile 37: | Zeile 51: | ||
{| class="wikitable" | {| class="wikitable" | ||
!width="200"| MATERIAL !!width="50"| Layer height !! width="50"| | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| Speed !! width="100"| Temperature (°C) !! width="100"|Who tried this !! width="100"| Notes | ||
|- | |- | ||
| PLA Neon Green || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | | PLA Neon Green || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | ||
|- | |- | ||
| PLA WHITE (no | | PLA WHITE (no name big spool) || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Looks better at higher temperature | ||
|- | |- | ||
| PLA Black bq || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | | PLA Black bq || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good. | ||
| Zeile 55: | Zeile 69: | ||
{| class="wikitable" | {| class="wikitable" | ||
!width="200"| MATERIAL !!width="50"| Layer height !! width="50"| | !width="200"| MATERIAL !!width="50"| Layer height !! width="50"| Speed !! width="100"|Temperature (°C) !! width="100"|Who tried this !! width="100"| Notes | ||
|- | |- | ||
| WHAT? || LAYER? ||SPEED|| TEMPERATURE || [[Benutzer:you|you]] || COMMENTS | | WHAT? || LAYER? ||SPEED|| TEMPERATURE || [[Benutzer:you|you]] || COMMENTS | ||
| Zeile 61: | Zeile 75: | ||
|} | |} | ||
| Zeile 96: | Zeile 95: | ||
** [https://blog.adafruit.com/2014/12/04/bq-witbox-review-by-tom-3dthursday-3dprinting/ Adafruit article] | ** [https://blog.adafruit.com/2014/12/04/bq-witbox-review-by-tom-3dthursday-3dprinting/ Adafruit article] | ||
** [https://chopmeister.blogspot.cz/2014/08/sifting-through-features-or-guide-to.html 'Sifting through the features or "The Guide to Not Buying a 3D Printer"']. | ** [https://chopmeister.blogspot.cz/2014/08/sifting-through-features-or-guide-to.html 'Sifting through the features or "The Guide to Not Buying a 3D Printer"']. | ||
===TODOs=== | |||
Setup raspberry pi with octoprint | |||
Design camera mount | |||
Mount camera | |||