Mendel90: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
Kay (Diskussion | Beiträge) (add software needed for 3d printing) |
Kay (Diskussion | Beiträge) (→Software: add GH repo to printrun) |
||
Zeile 32: | Zeile 32: | ||
=== Software === | === Software === | ||
* [http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver] | * [http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver] | ||
* [http://reprap.org/wiki/Printrun Printrun] | * [http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository]) | ||
* [http://slic3r.org/ Slic3r] | * [http://slic3r.org/ Slic3r] | ||
=== Resources === | === Resources === |
Version vom 10. Dezember 2014, 11:58 Uhr
3D-Scanner - CNC-Fräse - Laser - Reflow Oven - 3DPrinter (Prusa Mk3S, Prusa Mini) - Vinylplotter - Schweißinverter -Tischbohrmaschine - Drehbank - Ultraschallreiniger - Nähmaschinen
Mendel90 | |
Eigentümer: | Metalab |
Status: | Aktiv |
Erfordert Einschulung: | Ja |
Erfordert Authentisierung: | Ja |
Kostet: | 660EUR |
Hilfsbereite: | prikle |
- Location: Scannerraum
- Soup: http://reprap.soup.io/
- Mailinglist https://lists.metalab.at/mailman/listinfo/3d-printing
The Model: Mendel90
- Model Homepage: http://reprap.org/wiki/Mendel90
- Assembly Instruction/Doku: https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf
- Blog of Creator: http://hydraraptor.blogspot.com/
- THE SOURCE: https://github.com/nophead/Mendel90
- Order Detail: http://forums.reprap.org/read.php?94,196585
- If you are bored and want to see a complete build from zero to hero (from buildscript to finished printer) in less than two hours (including software setup; note that we will order the kit from the designer so we don't need half of the steps): https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z
- Latest maintenance:
- (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: Datei:Marlin-140830a.zip
- Support for arcs, doesn't accelerate/decelerate for polygons
- Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features
- (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: Datei:Marlin-140830a.zip
{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}
Software
Resources
- Settings for Slic3r and Printrun: Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip
- Lazzzor Design für Mendel90 Spule (by mika): Datei:Spule für mendel90.cdr
Finances Required to buy the printer:
- Printer (499 gbp): 615 Eur (excl Ust) , 738 Eur (incl 20% Ust)
- Shipping (35 gbp): 43 Eur (incl 20% Ust)
Total: 781 Eur (incl 20% Ust)- Total: 660 EUR (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))
3D Printer Workshop
Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen. Bei bedarf bitte bei prikle melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.
Nächster Workshop:
- Mi 10.09.2014 in der Bibliothek um 19Uhr
Teilnehmer:
Supporters - Mendel 90:
Name | Amount | an metalab bezahlt? |
---|---|---|
MiKa | €50 - Assembly Super Hero | ✔ (6.6.) |
wizard23 | €50 - Assembly Hero | ✔ (6.6.) |
Herbert | €50 - Assembly Hero | ✔ (6.6.) |
overflo | €50 - Assembly Hero i.A. (wir mussten seine Kiste pluendern weil ich vergessen hatte gaffer zu kaufen) | ✔ (9.6.) |
anlumo | €50 - Assembly Liege | ✔ (10.6.) |
cygenb0ck | €30 - Assembly Hero | ✔ (6.6.) |
Hetti | €20 - Assembly Hero | ✔ (6.6.) |
Grawu | €20 - Assembly Hero | |
Queltos | €0 - Assembly Hero | |
nex | €0 - Assembly Hero | |
prikle | €55 | ✔ (13.6.) |
clifford | €50 | ✔ (9.6.) |
Pepi | €50 | ✔ (13.6.) |
naxx | €50 | ✔ (10.6.) |
metachris | €30 | ✔ (6.6.) |
A | €30 | ✔ (12.6.) |
luto | €25 | ✔ (12.6.) |
simonrepp | €20 | ✔ (13.6.) |
Gem | €20 | ✔ (7.6.) |
leyrer | €50 | |
mind | €30 | |
Kewagi | €20 - Loetbefreit (ärztliches Attest liegt im core schrank) | |
Summe | €750 |