Witbox: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(payment information)
Zeile 58: Zeile 58:
'''Pay used filament'''
'''Pay used filament'''


?
* Calculate used material with your slicer or http://gcode.ws/
* Material costs are 0,10€/gramm
* Deposit appropriate amount in the 3D printing cash box.


===Wisdom Tables ===
===Wisdom Tables ===

Version vom 10. November 2015, 13:53 Uhr

Sprache: Deutsch
Subpages:
Witbox hat keine Unterseiten.


Witbox
Witbox.png
Eigentümer: Metalab
Status: Aktiv
Erfordert Einschulung: Ja
Erfordert Authentisierung: Ja
Kostet: 0.10 euro / gram
Hilfsbereite:



It is OK to use the printer as it is.

It is NOT OK to modify it in any way.

This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap.


Overview

Filament diameter 1.75mm

Layer height: 0.05-0.25 mm (0.2 is fast and looks good)

Material: PLA only

Firmware version: 1.4.2 ( 29.10.2015)

This machine was sponsored (better price) from 3dee.at

How to use it

Calibration (before every job @ metalab)

  • There is a calibration sheet inside the witbox.
  • Calibration is simple. Just follow the instructions on the menu.
  • Configuration -> Level plate

Load / Change Filament if neccessary - Careful not to entangle the filament!!

  • To change or unload the filament select the matching option from the menu
  • very gently apply some pull to the filament and you will feel that the filament is actually pulled for extraction first and after some seconds it is ejected
  • Once the filament is eject apply some more pullign force
  • when the filament comes loose pull sharply and remove the filament from the tube completely (also any long debris that might hang off the filament needs to get out)

Save your .gcode to the SD card

  • Start cura
  • Import .stl
  • Save to SD
  • Done.

Start job from menu

  • Select "Print from SD"
  • Select your job
  • Push dialing wheel- > job starts

Pay used filament

  • Calculate used material with your slicer or http://gcode.ws/
  • Material costs are 0,10€/gramm
  • Deposit appropriate amount in the 3D printing cash box.

Wisdom Tables

These settings have been tested and worked fine.

MATERIAL Layer height Speed Temperature (°C) Who tried this Notes
PLA Neon Green 0.1mm 80mm/sec 210C overflo Good.
PLA Neon Green 0.2mm 60mm/sec 220C 0x3d acceptable, 1st layer overhang curls, maybe too hot and slow
PLA WHITE (no name big spool) 0.1mm 80mm/sec 210C overflo Looks better at higher temperature
PLA Black bq 0.1mm 80mm/sec 210C overflo Good.
PLA Black bq 0.05mm 80mm/sec 210C overflo Very fine resolution!, Looks good! Used for TSA keyset
PLA transparent bq 0.1mm 80mm/sec 210C overflo Good.
PLA purple noname (3dee.at) 0.1mm 80mm/sec 210C overflo Good.


These settings caused some problems

MATERIAL Layer height Speed Temperature (°C) Who tried this Notes
WHAT? LAYER? SPEED TEMPERATURE you COMMENTS

Software

Cura for Witbox

Slic3r config files & manual

Slic3r zip contains 3 different config files:

  • Witbox_res_alta.ini -> 0.1 mm layer height
  • Witbox_res_baja.ini -> 0.3 mm layer height
  • Witbox_res_media.ini -> 0.2 mm layer height

Supporters


Diverse Links