Mendel90: Unterschied zwischen den Versionen
MiKa (Diskussion | Beiträge) KKeine Bearbeitungszusammenfassung |
MiKa (Diskussion | Beiträge) (→Software / prerequisites: added bit-rate poll, please levae it here until end of march) |
||
| Zeile 18: | Zeile 18: | ||
[http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])<br> | [http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])<br> | ||
[http://slic3r.org/ Slic3r]<br> | [http://slic3r.org/ Slic3r]<br> | ||
<br> | |||
Bit-rate poll until end of march 2015 (please vote with your Wiki user-ID or a well-known Metalab-handle, others will be ignored):<br> | |||
<br> | |||
{| class="wikitable" | |||
|- | |||
| 115,2 kbit/s only | |||
| ? | |||
|- | |||
| 115,2 and 230,4 kbit/s | |||
| ? | |||
|- | |||
|250 kbit/s (and lower) | |||
| [[Benutzer:MiKa | X]] | |||
|} | |||
If you can't support any of these, sorry you will have to use the 3D-Print station, which was prepared by Amir (Thanks & Kudos to Amir!) | |||
Please vote until end of march, then the firmware will be fixed. I will adapt the ARDUINO-source and upload the snapshot to the Wiki. | |||
(This section will be updated end of march, please leave it here, don't revert the page [[Benutzer:MiKa|MiKa]] ([[Benutzer Diskussion:MiKa|Diskussion]]) 22:40, 15. Feb. 2015 (CET)) | |||
= Resources = | = Resources = | ||
Version vom 15. Februar 2015, 21:40 Uhr
3D-Scanner - CNC-Fräse - Laser - Reflow Oven - 3DPrinter (Prusa Mk3S, Prusa Mini) - Vinylplotter - Schweißinverter -Tischbohrmaschine - Drehbank - Ultraschallreiniger - Nähmaschinen
| Mendel90 | |
| |
| Eigentümer: | Metalab |
| Status: | Aktiv |
| Erfordert Einschulung: | Ja |
| Erfordert Authentisierung: | Ja |
| Kostet: | 660EUR |
| Hilfsbereite: | prikle, MiKa |
Location: Scannerraum
Soup: http://reprap.soup.io/
Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing
Software / prerequisites
FTDI Chip VCP driver
Printrun (GitHub repository)
Slic3r
Bit-rate poll until end of march 2015 (please vote with your Wiki user-ID or a well-known Metalab-handle, others will be ignored):
| 115,2 kbit/s only | ? |
| 115,2 and 230,4 kbit/s | ? |
| 250 kbit/s (and lower) | X |
If you can't support any of these, sorry you will have to use the 3D-Print station, which was prepared by Amir (Thanks & Kudos to Amir!)
Please vote until end of march, then the firmware will be fixed. I will adapt the ARDUINO-source and upload the snapshot to the Wiki.
(This section will be updated end of march, please leave it here, don't revert the page MiKa (Diskussion) 22:40, 15. Feb. 2015 (CET))
Resources
Settings for Slic3r and Printrun: Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip
Lazzzor Design für Mendel90 Spule (by mika): Datei:Spule für mendel90.cdr
About the Mendel90
Mendel page on reprap.org
Assembly instructions/documentation (pdf)
Creator's own blog
Code source
Ordering a Mendel90 Kit
Video of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.
Latest maintenance:
- (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: Datei:Marlin-140830a.zip
- Support for arcs, doesn't accelerate/decelerate for polygons
- Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features
{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}
Finances Required to buy the printer:
- Printer (499 gbp): 615 Eur (excl Ust) , 738 Eur (incl 20% Ust)
- Shipping (35 gbp): 43 Eur (incl 20% Ust)
Total: 781 Eur (incl 20% Ust)- Total: 660 EUR (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))
3D Printer Workshop
Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen. Bei bedarf bitte bei prikle melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.
Nächster Workshop:
- Mi 10.09.2014 in der Bibliothek um 19Uhr
Teilnehmer:
Supporters - Mendel 90:
| Name | Amount | an metalab bezahlt? |
|---|---|---|
| MiKa | €50 - Assembly Super Hero | ✔ (6.6.) |
| wizard23 | €50 - Assembly Hero | ✔ (6.6.) |
| Herbert | €50 - Assembly Hero | ✔ (6.6.) |
| overflo | €50 - Assembly Hero i.A. (wir mussten seine Kiste pluendern weil ich vergessen hatte gaffer zu kaufen) | ✔ (9.6.) |
| anlumo | €50 - Assembly Liege | ✔ (10.6.) |
| cygenb0ck | €30 - Assembly Hero | ✔ (6.6.) |
| Hetti | €20 - Assembly Hero | ✔ (6.6.) |
| Grawu | €20 - Assembly Hero | |
| Queltos | €0 - Assembly Hero | |
| nex | €0 - Assembly Hero | |
| prikle | €55 | ✔ (13.6.) |
| clifford | €50 | ✔ (9.6.) |
| Pepi | €50 | ✔ (13.6.) |
| naxx | €50 | ✔ (10.6.) |
| metachris | €30 | ✔ (6.6.) |
| A | €30 | ✔ (12.6.) |
| luto | €25 | ✔ (12.6.) |
| simonrepp | €20 | ✔ (13.6.) |
| Gem | €20 | ✔ (7.6.) |
| leyrer | €50 | |
| mind | €30 | |
| Kewagi | €20 - Loetbefreit (ärztliches Attest liegt im core schrank) | |
| Summe | €750 |
