Mendel90: Unterschied zwischen den Versionen

Zeile 10:

}}

*Location: [[Scannerraum]]

Location: [[Scannerraum]]

*Soup: http://reprap.soup.io/

Soup: http://reprap.soup.io/

*Mailinglist https://lists.metalab.at/mailman/listinfo/3d-printing

Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing

=== ~~The Model: Mendel90~~ ===

=== Software / prerequisites ===

* Model Homepage: http://reprap.org/wiki/~~Mendel90~~

[http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver]

* Assembly Instruction/Doku: https://github.com/~~nophead~~/~~Mendel90~~/~~raw~~/~~master~~/~~dibond/manual/Mendel90_Dibond.pdf~~

[http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])

* Blog of Creator: ~~http~~:~~//hydraraptor~~.~~blogspot~~.~~com/~~

[http://slic3r.org/ Slic3r]

* THE SOURCE: ~~https~~:~~//github~~.~~com/nophead/~~Mendel90

* Order Detail: http://~~forums.~~reprap.org/~~read~~.~~php?94,196585~~

=== Resources ===

* If you are bored and want to see a complete build from zero to hero (from buildscript to finished printer) in less than two hours (including software setup; note that we will order the kit from the designer so we don't need half of the steps): https://~~www.youtube~~.com/~~playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z~~

Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]

* Latest maintenance:

Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]

** (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://~~github~~.~~com~~/~~neildarlow/Marlin~~) ~~Ducmentation and instructions on~~ http://~~forums~~.~~reprap~~.~~org~~/~~read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip~~]]

*** Support for arcs, doesn't accelerate/decelerate for polygons

=== About the Mendel90 ===

*** Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features

[http://reprap.org/wiki/Mendel90 Mendel page] on reprap.org

[https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf Assembly instructions/documentation] (pdf)

Creator's own [http://hydraraptor.blogspot.com/ blog]

[https://github.com/nophead/Mendel90 Code source]

[http://forums.reprap.org/read.php?94,196585 Ordering a Mendel90 Kit]

~~{{#ev~~:youtube~~|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}~~

[https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z Video] of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.

Latest maintenance:

* (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip]]

* Support for arcs, doesn't accelerate/decelerate for polygons

* Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features

~~=== Software / prerequisites ===~~

* [http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver]

* [http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])

* [http://slic3r.org/ Slic3r]

~~=== Resources ===~~

* Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]

* Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]

Finances Required to buy the printer: