HSC2011/Hardware: Unterschied zwischen den Versionen
Keine Bearbeitungszusammenfassung |
|||
| Zeile 51: | Zeile 51: | ||
|- style="background:#ccc;" | |- style="background:#ccc;" | ||
| Switch MIYAMA MS 245 || 1 || SW5 || S9 || connect over cable! | | Switch MIYAMA MS 245 || 1 || SW5 || S9 || connect over cable! | ||
|} | |} | ||
== Specification == | == Specification == | ||
Version vom 29. April 2011, 15:29 Uhr
Part list
| Partname | Amount | Position on PCB | Bauteilsortiment | known bugs |
|---|---|---|---|---|
| LED 5mm BLUE | 1 | D1 | - | |
| LED 5mm GREEN | 1 | D2 | G4 | |
| LED 5mm YELLOW | 1 | D3 | - | |
| LED 5mm RED | 1 | D4 | H4 | |
| Pushbutton | 4 | SW1, SW2, SW3, SW4 | E9 | |
| LF50CV | 1 | VREG1 | G6 | |
| Piezo beeper | 1 | U3 | S7 | |
| 2x16 Pol, RM 2.00 | 1 | U1 | C5 | needs 2x6 pin socket |
| RFM12B Radio module | 1 | U1 | K8 | |
| 28 PIN DIP Socket | 1 | IC4 | D9 | |
| ATMEGA328P | 1 | IC4 | - | |
| 10 uF Capacitor (elko) | 1 | C4 | E0 | |
| 22 pF Capacitor (ceramic) | 2 | C1, C2 | A2 | |
| 100 nF Capacitor (ceramic) | 1 | C3 | C2 | imprint unter loch |
| 16 Mhz Crystal | 1 | CRYSTAL1 | L0 | |
| 9V battery clip | 1 | JP3 | T3 | imprint should say +/- not J3 ;) |
| FTDI connector | 1 | JP4 | B6 | |
| Resistor 100 ohm | 1 | R10 | N1 | nicht bestücken! (R10) |
| Resistor 10K ohm | 1 | R9 | P3 | |
| Resistor 1K ohm | 7 | R5, R6, R7, R11, R12, R13 | O2 | |
| Resistor 680 ohm | 4 | R1,R2,R3,R4 | ? | am plan noch als 1k eingezeichnet |
| Resistor 4K7 ohm | 1 | R8 | - | |
| RGB LED 5mm | 1 | D5 | - | |
| Switch MIYAMA MS 245 | 1 | SW5 | S9 | connect over cable! |
Specification
Nodes are supposed to be equipped with:
- RF transceiver
- 4 buttons, labelled with digits, letters, colours (probably red / blue / green / yelow) and symbols (playstation style?)
- a LED for each button in matching colour
- an RGB LED
- a buzzer
- a 1-wire interface for authentication buttons (iButton)
For ease of development, they also get a serial interface ("FTDI cable" -- power supply + RX/TX + reset, also for flashing using a boot loader).
Implementation
Both for development and for the final version (as far as we know now), an ATMega328 is used; for development, encased in an Arduino, which also binds the RX/TX pins to a USB serial interface.
As an RF module, RFM12B is used.
The wiring is defined in an eagle file in the project repository.
RFM12B
A little very unprofessional test showed that with the current configuration (through-hole mounted RFM12B with the wire antennae bent to the opposite direction of the pins) with a sender at the whateverlab solder stations a receiver starts losing 6-long packets some steps outside the metalab door front and in the library. Even without further optimization, that should be sufficient for typical class rooms.
Experiments showed that sending a login packet takes about 10ms.
