Mendel90: Unterschied zwischen den Versionen
Metaz (Diskussion | Beiträge) |
Eest9 (Diskussion | Beiträge) Raum angepasst |
||
| (30 dazwischenliegende Versionen von 9 Benutzern werden nicht angezeigt) | |||
| Zeile 3: | Zeile 3: | ||
|image=m90.png | |image=m90.png | ||
|owner=Metalab | |owner=Metalab | ||
|status= | |status=zerlegt | ||
|requirestraining=Ja | |requirestraining=Ja | ||
|requiresauth=Ja | |requiresauth=Ja | ||
|cost=660EUR | |cost=660EUR | ||
|teachers=prikle | |teachers=[[User:prikle|prikle]],[[User:Hetti|Hetti]] | ||
}} | }} | ||
Location: [[WhateverLab]]<br> | |||
Soup: http://reprap.soup.io/<br> | |||
Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing<br> | |||
'''Handbuch für unseren 3Dprinter:''' [[/3DPrinter-Manual]] | |||
= Software / prerequisites = | |||
[http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver]<br> | |||
[http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])<br> | |||
[http://slic3r.org/ Slic3r]<br> | |||
= Resources = | |||
Slic3r Config Bundle for Mendel90 and Witbox: [[Datei:Slic3r_config_bundle_metalab_v1.zip]]<br> | |||
Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]<br> | |||
Settings for Slic3r (Octoprint): [[Datei:Mendel90_Octoprint_v2.ini.zip]]<br> | |||
Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]<br> | |||
= | = About the Mendel90 = | ||
[http://reprap.org/wiki/Mendel90 Mendel page] on reprap.org<br> | |||
[https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf Assembly instructions/documentation] (pdf)<br> | |||
Creator's own [http://hydraraptor.blogspot.com/ blog]<br> | |||
<br> | |||
[https://github.com/nophead/Mendel90 Code source]<br> | |||
[http://forums.reprap.org/read.php?94,196585 Ordering a Mendel90 Kit]<br> | |||
<br> | |||
[https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z Video] of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.<br> | |||
<br> | |||
Latest maintenance:<br> | |||
* (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip]]<br> | |||
* Support for arcs, doesn't accelerate/decelerate for polygons<br> | |||
* Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features | |||
{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}} | |||
Finances Required to buy the printer: | Finances Required to buy the printer: | ||
| Zeile 40: | Zeile 55: | ||
* '''Total: 660 EUR''' (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!)) | * '''Total: 660 EUR''' (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!)) | ||
= 3D Printer Workshop = | |||
Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen. | Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen. | ||
Bei bedarf bitte bei [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen. | Bei bedarf bitte bei [[Benutzer:MiKa|MiKa]] oder [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen. | ||
== Nächster Workshop:== | |||
* Mi '''10.09.2014''' in der [[Bibliothek]] um 19Uhr | |||
Teilnehmer: | Teilnehmer: | ||
# [[User:Min|Min]] | # [[User:Min|Min]] | ||
| Zeile 55: | Zeile 69: | ||
# [[User:Lumbric|lumbric]] | # [[User:Lumbric|lumbric]] | ||
# [[User:metaz|meta]] | # [[User:metaz|meta]] | ||
# [[User:A|A]] | |||
# [[User:jk|Jozef]] | |||
# [[User:You|You?]] | # [[User:You|You?]] | ||
= Supporters - Mendel 90: = | |||
{| class="wikitable" | {| class="wikitable" | ||