Mendel90: Unterschied zwischen den Versionen

aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
(Raum angepasst)
 
(31 dazwischenliegende Versionen von 10 Benutzern werden nicht angezeigt)
Zeile 3: Zeile 3:
|image=m90.png
|image=m90.png
|owner=Metalab
|owner=Metalab
|status=Aktiv
|status=zerlegt
|requirestraining=Ja
|requirestraining=Ja
|requiresauth=Ja
|requiresauth=Ja
|cost=660EUR
|cost=660EUR
|teachers=prikle
|teachers=[[User:prikle|prikle]],[[User:Hetti|Hetti]]
}}
}}


*Location: [[Scannerraum]]
Location: [[WhateverLab]]<br>
*Soup: http://reprap.soup.io/
Soup: http://reprap.soup.io/<br>
*Mailinglist https://lists.metalab.at/mailman/listinfo/3d-printing
Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing<br>


=== The Model: Mendel90 ===
'''Handbuch für unseren 3Dprinter:''' [[/3DPrinter-Manual]]
* Model Homepage: http://reprap.org/wiki/Mendel90
* Assembly Instruction/Doku: https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf
* Blog of Creator: http://hydraraptor.blogspot.com/
* THE SOURCE: https://github.com/nophead/Mendel90
* Order Detail: http://forums.reprap.org/read.php?94,196585
* If you are bored and want to see a complete build from zero to hero (from buildscript to finished printer) in less than two hours (including software setup; note that we will order the kit from the designer so we don't need half of the steps): https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z
* Latest maintenance:
** (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip]]
*** Support for arcs, doesn't accelerate/decelerate for polygons
*** Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features


= Software / prerequisites =
[http://www.ftdichip.com/Drivers/VCP.htm FTDI Chip VCP driver]<br>
[http://reprap.org/wiki/Printrun Printrun] ([https://github.com/kliment/Printrun GitHub repository])<br>
[http://slic3r.org/ Slic3r]<br>


{{#ev:youtube|y6Kc1RyHgtw}}
= Resources =
Slic3r Config Bundle for Mendel90 and Witbox: [[Datei:Slic3r_config_bundle_metalab_v1.zip]]<br>
Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]<br>
Settings for Slic3r (Octoprint): [[Datei:Mendel90_Octoprint_v2.ini.zip]]<br>
Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]<br>


=== Resources ===
= About the Mendel90 =
* Settings for Slic3r and Printrun: [[Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip]]
[http://reprap.org/wiki/Mendel90 Mendel page] on reprap.org<br>
* Lazzzor Design für Mendel90 Spule (by mika): [[Datei:Spule_für_mendel90.cdr]]
[https://github.com/nophead/Mendel90/raw/master/dibond/manual/Mendel90_Dibond.pdf Assembly instructions/documentation] (pdf)<br>
Creator's own [http://hydraraptor.blogspot.com/ blog]<br>
<br>


[https://github.com/nophead/Mendel90 Code source]<br>
[http://forums.reprap.org/read.php?94,196585 Ordering a Mendel90 Kit]<br>
<br>
[https://www.youtube.com/playlist?list=PLNUL7DzXzp_JqA92h6eeVH8XwwLVZ_C0Z Video] of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.<br>
<br>
Latest maintenance:<br>
* (2014-Aug-29 MiKa) Firmware upgrade: Upgraded to Marlin_v1_Mendel90 by Neil Darlow (github: https://github.com/neildarlow/Marlin) Ducmentation and instructions on http://forums.reprap.org/read.php?292,321160 Parametes in config.h adapted and calibrated. Snapshot of the Arduino sketch as currently installed: [[Datei:Marlin-140830a.zip]]<br>
* Support for arcs, doesn't accelerate/decelerate for polygons<br>
* Support for PID-regulated heatbed instead of on/off (aka "bang-bang" mode) and some more features
{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}


Finances Required to buy the printer:
Finances Required to buy the printer:
Zeile 40: Zeile 55:
* '''Total: 660 EUR''' (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))
* '''Total: 660 EUR''' (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))


== 3D Printer Workshop ==
= 3D Printer Workshop =
Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen.
Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen.
Bei bedarf bitte bei [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.
Bei bedarf bitte bei [[Benutzer:MiKa|MiKa]] oder [[Benutzer:prikle|prikle]] melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.
 
== Nächster Workshop:==
* Mi '''10.09.2014''' in der [[Bibliothek]] um 19Uhr


===Nächster Workshop:===
*31.08.2014 in der [[Bibliothek]] um 16Uhr
!!! Abgesagt !!!
*03.09.2014 in der [[Bibliothek]] um 19Uhr
Teilnehmer:
Teilnehmer:
# [[User:Min|Min]]
# [[User:Min|Min]]
Zeile 54: Zeile 68:
# [[User:Uberhaxlor|Uberhaxlor]]
# [[User:Uberhaxlor|Uberhaxlor]]
# [[User:Lumbric|lumbric]]
# [[User:Lumbric|lumbric]]
# [[User:metaz|meta]]
# [[User:A|A]]
# [[User:jk|Jozef]]
# [[User:You|You?]]
# [[User:You|You?]]


== Supporters - Mendel 90: ==  
= Supporters - Mendel 90: =


{| class="wikitable"
{| class="wikitable"

Aktuelle Version vom 31. Januar 2022, 15:47 Uhr


Mendel90
M90.png
Eigentümer: Metalab
Status: zerlegt
Erfordert Einschulung: Ja
Erfordert Authentisierung: Ja
Kostet: 660EUR
Hilfsbereite: prikle,Hetti


Location: WhateverLab
Soup: http://reprap.soup.io/
Mailinglist: https://lists.metalab.at/mailman/listinfo/3d-printing

Handbuch für unseren 3Dprinter: /3DPrinter-Manual

Software / prerequisites

FTDI Chip VCP driver
Printrun (GitHub repository)
Slic3r

Resources

Slic3r Config Bundle for Mendel90 and Witbox: Datei:Slic3r config bundle metalab v1.zip
Settings for Slic3r and Printrun: Datei:Slic3r1.0.1-mendel90-v1.1.2.ini.zip
Settings for Slic3r (Octoprint): Datei:Mendel90 Octoprint v2.ini.zip
Lazzzor Design für Mendel90 Spule (by mika): Datei:Spule für mendel90.cdr

About the Mendel90

Mendel page on reprap.org
Assembly instructions/documentation (pdf)
Creator's own blog

Code source
Ordering a Mendel90 Kit

Video of complete build from zero to hero (from build script to finished printer) in less than two hours (including software setup); note that we ordered the kit from the designer so we didn't need half of the steps.

Latest maintenance:


{{#ev:youtube|y6Kc1RyHgtw}} {{#ev:youtube|wNk47pjvXbM}}

Finances Required to buy the printer:

  • Printer (499 gbp): 615 Eur (excl Ust) , 738 Eur (incl 20% Ust)
  • Shipping (35 gbp): 43 Eur (incl 20% Ust)
  • Total: 781 Eur (incl 20% Ust)
  • Total: 660 EUR (Metalab gets a special price because the kit designer is a fan of OpenSCAD (the complete Mendel90 design is made in OpenSCAD, check out the source, now!))

3D Printer Workshop

Beim 3D Printer Workshop bekommt ihr die nötige Einschulung um den 3D Drucker (Mendel90) Verwenden zu dürfen. Bei bedarf bitte bei MiKa oder prikle melden. Es gibt auch die Möglichkeit einen Termin für Einzeleinschullungen auszumachen.

Nächster Workshop:

Teilnehmer:

  1. Min
  2. Metachris
  3. Leo
  4. Uberhaxlor
  5. lumbric
  6. meta
  7. A
  8. Jozef
  9. You?

Supporters - Mendel 90:

Name Amount an metalab bezahlt?
MiKa €50 - Assembly Super Hero ✔ (6.6.)
wizard23 €50 - Assembly Hero ✔ (6.6.)
Herbert €50 - Assembly Hero ✔ (6.6.)
overflo €50 - Assembly Hero i.A. (wir mussten seine Kiste pluendern weil ich vergessen hatte gaffer zu kaufen) ✔ (9.6.)
anlumo €50 - Assembly Liege ✔ (10.6.)
cygenb0ck €30 - Assembly Hero ✔ (6.6.)
Hetti €20 - Assembly Hero ✔ (6.6.)
Grawu €20 - Assembly Hero
Queltos €0 - Assembly Hero
nex €0 - Assembly Hero
prikle €55 ✔ (13.6.)
clifford €50 ✔ (9.6.)
Pepi €50 ✔ (13.6.)
naxx €50 ✔ (10.6.)
metachris €30 ✔ (6.6.)
A €30 ✔ (12.6.)
luto €25 ✔ (12.6.)
simonrepp €20 ✔ (13.6.)
Gem €20 ✔ (7.6.)
leyrer €50
mind €30
Kewagi €20 - Loetbefreit (ärztliches Attest liegt im core schrank)
Summe €750


Abgerufen von „https://metalab.at/alpakaparty/index.php?title=Mendel90&oldid=71487“