WhateverLab/Umbau: Unterschied zwischen den Versionen

← Zum vorherigen Versionsunterschied

VisuellWikitext

@@ Zeile 27: / Zeile 27: @@
 Costs:
-We already have most of the equiment and material necessary, so only minor supplements are needed.
+We already have most of the equiment and material necessary, so only minor supplements are needed (Putz, Tiefengund, Spachtelmasse, misc. tools)
-* Putz, Tiefengund and Spachtelmasse: FIXME
-* Misc. tools: FIXME
 === Floor ===
@@ Zeile 47: / Zeile 44: @@
 : Trockenzeit abhängig von der Raumtemp., mit 2 Tagen pro Anstrich rechnen, Grund und Versiegelung beinhalten Lösungsmittel, Tür zum Hauptraum gut abdichten und hofseitig begehen, bis zur Wand streichen/rollen, PVC Sesselleise erst nachher
 : 4 verschiedene Farben lagernd ([[User:Philip|Philip]]: ''"wenig sexy"''), Lieferzeit anderer Farben (zB. Weiss) max. 14 Tage. eventuell bissl Flitte^W Feenstaub einstreuen
+Misc costs: Parkett Fugendicht, Montageschaum, ca. 50 euro
 === Electricity ===
-Ideally, we should subdivide the lab into at least 3 indepentant
+The WEL will be subdivided into 2 independent circuits wired from the fuse cabinet in the corner, one will serve power for the heavy machinery lab, and one for the remaining power and lights.
-circuits. The main reason for this is that short circuits are more
-likely to happen in an electronics lab than anywhere else. In
-addition, the future machine room will draw a lot of power, so it
-should have a dedicated circuit.
-We might be able to reuse some cable canals inside the walls. If not,
+All wiring will be done "aufputz", since the quality of the wiring inside the walls are questionable.
-we'll wire the circuits externally.
-A generous amount of outlets has to be provided for the work places
+Lighting should be neutral and bright and without too much flickering (e.g. neon with EVG).
-due to the amount of electronic apparatus being used.
-Lighting should be neutral and bright.
 == Phase 1 Tasks ==
@@ Zeile 85: / Zeile 76: @@
   |-
   |Paint all walls and ceiling
-  | 80%
+  | 100%
   |
   |-
   |Final touch
+ | 100%
   |
- |
 |}
@@ Zeile 106: / Zeile 97: @@
   |-
   |Build the missing piece just after the doorstep
+ | 100%
+ |
+ |-
+ |Strengthen weak spots in the floor
   | 100%
   |
   |-
   |Fill all cracks and edges
-  | 20%
+  | 100%
-  | Using foam for the edges
+  |
   |-
   |Sand down the floor to make it even
-  |
+  |100%
-  |
+  |Hopefully it's even enough now..
   |-
   |Apply coating
-  |
+  | 100%
   |
   |-
   |Final touch
-  |
+  | 100%
-  |
+  | Ready to rumble!
 |}
@@ Zeile 135: / Zeile 130: @@
   |-
   |Evaluate the state of the current wiring
-  |
+  |100%
-  |
+  |Existing in-wall wires should be cut off and forgotten about
   |-
-  |Decide on techincal solution wrt. circuits, fuses, earth leakage breaker etc.
+  |Decide on technical solution wrt. circuits, fuses, earth leakage breaker etc.
-  |
+  |100%
-  |
+  |We have 3 x 16A + a FI dedicated to the WEL already in place
   |-
-  |Decide on lighting solution
+  |Decide on light & power solution
-  |
+  |100%
   |
   |-
   |Aquire the necessary equipment (lamps, cables, channels, outlets, switches etc.)
-  |
+  |100%
-  |
+  |([http://www.orion.co.at/de/docs/stores/at/w1070.htm source for library/WEL lamps])
   |-
   |Build
-  |
+  |100%
   |
   |-
   |Final touch
-  |
+  | 100%
   |
 |}
-= Plans & Ideas for Further Phases =
+= Further Phases =
-FIXME
+* Make heavy machinery lab closable to limit dust -> done (new room)
+* More outlets in the remaining corners of the lab -> partially done
+* Permanent network cabling -> done
+* More (and orderly) shelving
+* Fixed and labeled positions for oszis, soldering stations, etc
+* Stairs to the big window (since Hvy Mchnry exit will be unusable for a while)
 [[Kategorie:Räume]] [[Kategorie:WhateverLab]]