Witbox: Unterschied zwischen den Versionen

(19 dazwischenliegende Versionen von 9 Benutzern werden nicht angezeigt)

Zeile 4:

|image=Witbox.png

|owner=Metalab

|status=~~Aktiv~~

|status=Inaktiv

|requirestraining=Ja

|requiresauth=~~[[Druckerkammerl|~~Ja~~]] ???~~

|requiresauth=Ja

|cost=~~????~~

|cost=0.10 euro / gram

|teachers=~~{{Druckermenschen}} ???~~

|teachers=[[User:Hetti|Hetti]]

}}

{| width="100%"

__TOC__

'''It is OK to use the printer as it is.'''

'''It is NOT OK to modify it in any way.'''

This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap.

'''If you notice any problems with the machine''' (maintenance required, damage) '''you are required to report your observations'''. Please use either subscribers-only mailing lists intern@ or [https://lists.metalab.at/mailman/listinfo/3d-printing 3d-printing@], the [https://metalab.at/issues/ issue tracker] or mail to http://metalab.at/wiki/images/2/2b/Core.png.

===Overview===

Zeile 19:

Zeile 27:

Material: PLA only

Firmware version: ~~???~~

Firmware version: 1.4.2 ( 29.10.2015)

This machine was sponsored (better price) from [http://www.3dee.at/ 3dee.at]

===How to use it===

Calibration

'''Calibration (before every job @ metalab)'''

* There is a calibration sheet inside the witbox.

* Calibration is simple. Just follow the instructions on the menu.

* Configuration -> Level plate

Load / ~~Unload~~ Filament

'''Load / Change Filament if neccessary - Careful not to entangle the filament!!'''

* To change or unload the filament select the matching option from the menu

* very gently apply some pull to the filament and you will feel that the filament is actually pulled for extraction first and after some seconds it is ejected

* Once the filament is eject apply some more pullign force

* when the filament comes loose pull sharply and remove the filament from the tube completely (also any long debris that might hang off the filament needs to get out)

~~Insert~~ a ~~spool~~

'''Save your .gcode to the SD card'''

* Start cura

* Import .stl

* Save to SD

* You can use folders with your nickname to group your files on an SD card. The Witbox' display will only show the first 19 characters of a filename. So make sure you can distinguish multiple files within that limit so you always print the correct file.

* Done.

~~Careful not to entangle the filament!!~~

'''Start job from menu'''

* Select "Print from SD"

* Select your job

* Push dialing wheel- > job starts

'''Pay used filament'''

~~===TODOs===~~

* Calculate used material with your slicer or http://gcode.ws/

* Material costs are 0,10€/gramm

* Deposit appropriate amount in the 3D printing cash box.

~~Setup raspberry pi with octoprint~~

===Wisdom Tables ===

These settings have been tested and worked fine. {{Yes}}

~~Design camera mount~~

{| class="wikitable"

|-

| PLA Neon Green || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good.

|-

| PLA Neon Green || 0.2mm ||60mm/sec || 220C || [[Benutzer:0x3d|0x3d]] || acceptable, 1st layer overhang curls, maybe too hot and slow

|-

| PLA WHITE (no name big spool) || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Looks better at higher temperature

|-

| PLA Black bq || 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good.

|-

| PLA Black bq || 0.05mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Very fine resolution!, Looks good! Used for [https://github.com/Xyl2k/TSA-Travel-Sentry-master-keys TSA keyset]

|-

| PLA transparent bq|| 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good.

|-

| PLA purple noname (3dee.at)|| 0.1mm ||80mm/sec || 210C || [[Benutzer:Overflo|overflo]] || Good.

|-

| PLA blue noname (3dee.at)|| 0.2mm ||80mm/sec || 210C || [[Benutzer:Don|don]] || Large rectangular bottom layer was not sticking to the plate with Cura's default Witbox advanced settings. Default first layer thickness = 0.3mm and default first layer speed = 20mm/sec. I changed these to 0.2mm and 80mm/sec respectively and then it worked perfectly.

|-

|}

~~Mount camera~~

These settings caused some problems {{No}}

===~~Policies~~===

{| class="wikitable"

|-

| WHAT? || LAYER? ||SPEED|| TEMPERATURE || [[Benutzer:you|you]] || COMMENTS

|-

|}

~~It is OK to use the printer as it is~~.

=== Software ===

[http://www.bq.com/gb/support/witbox Cura for Witbox]

~~It is NOT OK to modify it in any way~~.

[http://www.bq.com/gb/support/witbox Slic3r config files & manual]

~~This is a consumer grade semi professional machine, if you want to tinker with a 3d-printer check out the mendel90 reprap.~~

Slic3r zip contains 3 different config files:

* Witbox_res_alta.ini -> 0.1 mm layer height

* Witbox_res_baja.ini -> 0.3 mm layer height

* Witbox_res_media.ini -> 0.2 mm layer height

~~=== Software ===~~

~~[http://www.bq.com/gb/support/witbox Cura for Witbox]~~

Metalab config bundle for slic3r: [[Datei:Slic3r_config_bundle_metalab_v1.zip]]

=== [[Diskussion:Witbox|Supporters]] ===

Zeile 61:

Zeile 116:

=== Diverse Links ===

* [http://gcode.ws/ Gcode.ws] Analyse gcode for prize and duration (usefull if you use slic3r)

* [https://github.com/bq/witbox Design] of the 3D-Printer is under CreativeCommons licence.

* [http://www.heise.de/make/artikel/FDM-3D-Drucker-im-Vergleich-2545710.html heise.de comparsion of different printers (German)] (pro for our use: we can buy replacement parts easily in Vienna)