Metalock2.0: Unterschied zwischen den Versionen
Pete (Diskussion | Beiträge) Keine Bearbeitungszusammenfassung |
Pete (Diskussion | Beiträge) |
||
| (7 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt) | |||
| Zeile 7: | Zeile 7: | ||
* is a custom built lock system and the successor of [[Metalock]] | * is a custom built lock system and the successor of [[Metalock]] | ||
* it consists of a DOCKSTAR embedded linux system, an EMZY sponsored by EVVA and an Arduino | * it consists of a DOCKSTAR embedded linux system, an EMZY sponsored by EVVA and an Arduino | ||
* An Raspberry Pi for serving the Door Status as a Website | |||
== Door Status == | == Door Status == | ||
Door Status is working again: | Door Status is working again since July 2018 : <br> | ||
Available in the local network over IPv4: http://10.20.30.77 | Available in the local network over IPv4: http://10.20.30.77 + IPv6: http://[2a02:61:a2::d8]/ | ||
Globally available under http://eingang.metalab.at (IPv4 + IPv4) | |||
IPv4+IPv6 Mirror exists under https://hodors.cyber.coffee<br> | |||
== How == | == How == | ||
* Only Software of Door Status is on Github | * Only Software of Door Status is on Github. | ||
Lessons learned: <br> | Lessons learned: <br> | ||
| Zeile 21: | Zeile 25: | ||
Hardware documentation | Hardware documentation | ||
* tbd (how is everything connected) | * tbd (how is everything connected) | ||
* Door Status is wired directly to the door status switch. Voltage divider is between the 2 connectors of the soor status Switch. | |||
From 5V to 3V for the Raspberry Pi GPIO. 22K Ohm + 33K Ohm Resistors. | |||
Software documentation | Software documentation <br> | ||
<b>Metalock2.0</b> | |||
* TBD ;) (yeah right..) (pitfalls, config, buildprocess) | * TBD ;) (yeah right..) (pitfalls, config, buildprocess) | ||
* IP: 10.20.30.77 (local IPv4 of | * IP: 10.20.30.20 (local IPv4 of DOCKSTAR) | ||
<b>Door Status:</b> | |||
* IP: 10.20.30.77 (local IPv4 of Raspberry Pi) | |||
* Software of Doorstatus: https://github.com/Metalab/metadoor | |||
== Reference == | == Reference == | ||
Aktuelle Version vom 23. März 2021, 18:30 Uhr
BETA!!! Running in Production since years
Currently BETA TESTING please leave all your experiences, ideas, bugreports, suggestions on the discussion page Diskussion:Metalock running since years quite good!
Metalock2.0
- is a custom built lock system and the successor of Metalock
- it consists of a DOCKSTAR embedded linux system, an EMZY sponsored by EVVA and an Arduino
- An Raspberry Pi for serving the Door Status as a Website
Door Status
Door Status is working again since July 2018 :
Available in the local network over IPv4: http://10.20.30.77 + IPv6: http://[2a02:61:a2::d8]/
Globally available under http://eingang.metalab.at (IPv4 + IPv4)
IPv4+IPv6 Mirror exists under https://hodors.cyber.coffee
How
- Only Software of Door Status is on Github.
Lessons learned:
The Setup is not documented and quite complex.
Hardware documentation
- tbd (how is everything connected)
- Door Status is wired directly to the door status switch. Voltage divider is between the 2 connectors of the soor status Switch.
From 5V to 3V for the Raspberry Pi GPIO. 22K Ohm + 33K Ohm Resistors.
Software documentation
Metalock2.0
- TBD ;) (yeah right..) (pitfalls, config, buildprocess)
- IP: 10.20.30.20 (local IPv4 of DOCKSTAR)
Door Status:
- IP: 10.20.30.77 (local IPv4 of Raspberry Pi)
- Software of Doorstatus: https://github.com/Metalab/metadoor
Reference
Who
Doorstatus Software & Hardware:
- Brought to you by Nico, Nini, Ripper, Phileas, and many other lovely Metalab people <3
- Resurrected™ by Hetti
Videos
tbd
Photos
tbd
Future
We are planning to replace the whole System in the (near) future with an simpler and better setup. Metalock 3.0 - TBA -
