Blinkentunnel 2.0: Unterschied zwischen den Versionen
Keine Bearbeitungszusammenfassung |
Pete (Diskussion | Beiträge) K Textersetzung - „ente“ durch „Usergraveyard“ |
||
| (9 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
{{Projekt | {{Projekt | ||
|image=bt2_5.jpg | |image=bt2_5.jpg | ||
|involved=[[User:overflo]] | |involved=[[User:overflo|overflo]] + lots of helpers | ||
|startdate=17.11.2016 | |startdate=17.11.2016 | ||
|status=completed | |status=completed | ||
| Zeile 11: | Zeile 11: | ||
* The successor of the famous [[Blinkentunnel|Blinkentunnel]] project | * The successor of the famous [[Blinkentunnel|Blinkentunnel]] project | ||
* | * Located at the passway between our [[Hauptraum|mainroom]] and the [[Vorraum|entrance room]] | ||
* There are 18 acryl sticks mounted | * There are 18 acryl sticks mounted to the ceiling, with 12mm WS2801 Pixels mounted on each side and shining inwards | ||
* They are controlled from an ESP8266 custom made PCB with a custom firmware that supports ARTNET see '''[[Blinkybutton]]''' | * They are controlled from an ESP8266 custom made PCB with a custom firmware that supports ARTNET see '''[[Blinkybutton]]''' | ||
== How == | == How == | ||
| Zeile 24: | Zeile 23: | ||
So [[Benutzer:Overflo|Overflo]] spent a long weekend designing a little PCB and writing some custom firmware for the ESP8266 based board he made and called the result '''[[Blinkybutton]]''' | So [[Benutzer:Overflo|Overflo]] spent a long weekend designing a little PCB and writing some custom firmware for the ESP8266 based board he made and called the result '''[[Blinkybutton]]''' | ||
The setup Boots in ~ | The setup Boots in ~1.2 seconds and diplays a classic rainbow animation. | ||
It tries to connect to the WLAN and if that fails it opens its own Accesspoint called ARTNET- | It tries to connect to the WLAN and if that fails it opens its own Accesspoint called ARTNET-NODE_26_C6 | ||
When you connect there it opens a captive portal configuration interface where you can setup the parameters like: | When you connect there it opens a captive portal configuration interface where you can setup the parameters like: | ||
| Zeile 32: | Zeile 31: | ||
* WLAN to connect to | * WLAN to connect to | ||
* Password | * Password | ||
* ARTNET universe ID (currently set to | * ARTNET universe ID (currently set to 0) | ||
* ARTNET OFFSET (currently set to 0) | * ARTNET OFFSET (currently set to 0) | ||
* Static IP Address (unconfigured , it uses DHCP) | * Static IP Address (unconfigured , it uses DHCP) | ||
| Zeile 42: | Zeile 41: | ||
It returns to displaying the rainbow when there is no data received for >5 minutes. | It returns to displaying the rainbow when there is no data received for >5 minutes. | ||
== Media == | |||
{| border=0 cellspacing="0" style="border-collapse:collapse;" | |||
|- | |||
|style="vertical-align:top"| {{#ev:youtube|Qqj3KswTHXA}} | |||
|style="vertical-align:top"| {{#ev:youtube|cGTwQ_YIc7A}} | |||
|- | |||
|style="vertical-align:top"| {{#ev:youtube|pzjMtXXwoAo}} | |||
|style="vertical-align:top"| {{#ev:youtube|_P_PDajuoog}} | |||
|- | |||
|style="vertical-align:top"|[[Bild:bt2_4.jpg|thumb|400px]] | |||
|style="vertical-align:top"|[[Bild:bt2_2.jpg|thumb|400px]] | |||
|- | |||
|style="vertical-align:top"|[[Bild:bt2_3.jpg|thumb|400px]] | |||
|style="vertical-align:top"|[[Bild:bt2_5.jpg|thumb|400px]] | |||
|- | |||
|style="vertical-align:top"|[[Bild:bt2_0.jpg|thumb|400px]] | |||
|style="vertical-align:top"|[[Bild:Kabelsalat.jpeg|thumb|400px|Kabelsalat ist gesund (Assembly session)]] | |||
|} | |||
== How to ART-net== | == How to ART-net== | ||
| Zeile 52: | Zeile 71: | ||
* All done | * All done | ||
== | |||
== People involved == | |||
* [[Benutzer:Overflo|Overflo]] - idea, electronics, soldering, firmware | * [[Benutzer:Overflo|Overflo]] - idea, electronics, soldering, firmware | ||
* [[Benutzer:Redplanet|redplanet]] - stein des anstosses, soldering | * [[Benutzer:Redplanet|redplanet]] - stein des anstosses, soldering | ||
* [[ | * [[User:Usergraveyard|Usergraveyard]] - soldering, assembly line | ||
* [[Benutzer:Min|min]] - soldering, assembly line | * [[Benutzer:Min|min]] - soldering, assembly line | ||
* [[Benutzer:Nioram|nico]] - QLC+ setup, effects, installation | * [[Benutzer:Nioram|nico]] - QLC+ setup, effects, installation | ||
| Zeile 62: | Zeile 82: | ||
* Other people I forgot to mention. Sorry! Please add yourself here | * Other people I forgot to mention. Sorry! Please add yourself here | ||
== References / Links == | == References / Links == | ||
| Zeile 91: | Zeile 90: | ||
* [http://download.arduino.org/products/UNOWIFI/0A-ESP8266-Datasheet-EN-v4.3.pdf ESP8266 Datasheet] | * [http://download.arduino.org/products/UNOWIFI/0A-ESP8266-Datasheet-EN-v4.3.pdf ESP8266 Datasheet] | ||
* Blinkybutton @ (hackerspaceshop) TBD | * Blinkybutton @ (hackerspaceshop) TBD | ||
* [[Artnet]] | |||
* [https://github.com/overflo23/ESP8266_ARTNET_WS2801 github] '''FIRMWARE''' | |||
[[Kategorie:Infrastruktur]] | |||
[[Kategorie:Projekte]] | |||