Blinkentunnel 2.0: Unterschied zwischen den Versionen

(24 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)

Zeile 1:

{{Projekt

|image=bt2_5.jpg

|involved=[[User:overflo|overflo]] + lots of helpers

|startdate=17.11.2016

|status=completed

|wtf=artsy fartsy blinky thingy

|hidden=false

}}

== Blinkentunnel 2.0 ==

* ~~the~~ successor of the famous [[Blinkentunnel|Blinkentunnel]] project

* The successor of the famous [[Blinkentunnel|Blinkentunnel]] project

* ~~is located~~ at the passway between our [[Hauptraum|mainroom]] and the [[Vorraum|entrance room]]

* Located at the passway between our [[Hauptraum|mainroom]] and the [[Vorraum|entrance room]]

* ~~there~~ are 18 acryl sticks mounted on the ceiling, with 12mm WS2801 Pixels mounted on each side and shining inwards

* There are 18 acryl sticks mounted to the ceiling, with 12mm WS2801 Pixels mounted on each side and shining inwards

* ~~they~~ are controlled from an ESP8266 custom made PCB with a custom firmware that supports ARTNET see '''[[Blinkybutton]]'''

* They are controlled from an ESP8266 custom made PCB with a custom firmware that supports ARTNET see '''[[Blinkybutton]]'''

== How ==

We built the original Blinkentunnel 7 years ago using Shiftbrites and an Arduino based on the Atmega168.

Zeile 12:

Zeile 22:

When [[Benutzer:Redplanet|redplanet]] tried to fix the old installation it became clear that we should replace the leds and that led to also replacing the ancient controller with something modern.

So [[Benutzer:Overflo|Overflo]] spent a long weekend designing a little PCB and writing some custom firmware for the ESP8266 based board he made and called the result ''Blinkybutton''

So [[Benutzer:Overflo|Overflo]] spent a long weekend designing a little PCB and writing some custom firmware for the ESP8266 based board he made and called the result '''[[Blinkybutton]]'''

The setup Boots in ~3 seconds and diplays a classic rainbow animation.

The setup Boots in ~1.2 seconds and diplays a classic rainbow animation.

It tries to connect to the WLAN and if that fails it opens its own Accesspoint called ARTNET-~~NODE_26_?~~

It tries to connect to the WLAN and if that fails it opens its own Accesspoint called ARTNET-NODE_26_C6

When you connect there it opens a captive portal configuration interface where you can setup the parameters like:

Zeile 21:

Zeile 31:

* WLAN to connect to

* Password

* ARTNET universe ID (currently set to 3)

* ARTNET universe ID (currently set to 0)

* ARTNET OFFSET (currently set to 0)

* Static IP Address (unconfigured , it uses DHCP)

Zeile 31:

Zeile 41:

It returns to displaying the rainbow when there is no data received for >5 minutes.

== Media ==

== ~~Who~~ ==

{| border=0 cellspacing="0" style="border-collapse:collapse;"

|-

|style="vertical-align:top"| {{#ev:youtube|Qqj3KswTHXA}}

|style="vertical-align:top"| {{#ev:youtube|cGTwQ_YIc7A}}

|-

|style="vertical-align:top"| {{#ev:youtube|pzjMtXXwoAo}}

|style="vertical-align:top"| {{#ev:youtube|_P_PDajuoog}}

|-

|style="vertical-align:top"|[[Bild:bt2_4.jpg|thumb|400px]]

|style="vertical-align:top"|[[Bild:bt2_2.jpg|thumb|400px]]

|-

|style="vertical-align:top"|[[Bild:bt2_3.jpg|thumb|400px]]

|style="vertical-align:top"|[[Bild:bt2_5.jpg|thumb|400px]]

|-

|style="vertical-align:top"|[[Bild:bt2_0.jpg|thumb|400px]]

|}

== How to ART-net==

* Install [http://www.qlcplus.org/downloads.html QLC+]

* Connect to metalights WiFi (password: metalights)

* Configure QLC+ so it outputs on the 192.168.88.255 address

* Define a 18x2 matrix fixture

* Use the matrix-functions on this fixture

* Combine with all kinds of other effects, inputs, masks and what not..

* All done

== People involved ==

* [[Benutzer:Overflo|Overflo]] - idea, electronics, soldering, firmware

* [[Benutzer:Redplanet|redplanet]] - ~~idea~~, soldering

* [[Benutzer:Redplanet|redplanet]] - stein des anstosses, soldering

* [[~~Benutzer~~:~~ente~~|~~ente~~]] - soldering, assembly line

* [[User:Usergraveyard|Usergraveyard]] - soldering, assembly line

* [[Benutzer:Min|min]] - soldering, assembly line

* [[Benutzer:Nioram|nico]] - QLC+ setup, effects, installation

* max - soldering, installation

* [[Benutzer:ripper]] - installation, parts

* [[Benutzer:ripper|ripper]] - installation, parts

* Other people I forgot to mention. Sorry! Please add yourself here

~~== Source ==~~

~~[https://github.com/overflo23/ESP8266_ARTNET_WS2801 Firmware @ github]~~

== ~~Videos~~ ==

== References / Links ==

~~{{#ev:vimeo|4772433}}~~

~~TBD~~

~~== Photos ==~~

~~{| border=0 cellspacing="0" style="border-collapse:collapse;"~~

|-

|}

* [http://www.qlcplus.org/downloads.html QLC+] Light Controlling Software

* [http://cdn.sparkfun.com/datasheets/Components/LED/WS2801%20LED%20pixel.pdf WS2801 Datasheet]

* [http://download.arduino.org/products/UNOWIFI/0A-ESP8266-Datasheet-EN-v4.3.pdf ESP8266 Datasheet]

* Blinkybutton @ (hackerspaceshop) TBD

* [[Artnet]]

* [https://github.com/overflo23/ESP8266_ARTNET_WS2801 github] '''FIRMWARE'''

~~== References / Links ==~~

[[Kategorie:Infrastruktur]]

[[Kategorie:Projekte]]

* WS2801

* ESP8266

* Blinkybutton (hackerspaceshop)