SMD-Stencils selber machen: Unterschied zwischen den Versionen
Keine Bearbeitungszusammenfassung |
|||
| Zeile 22: | Zeile 22: | ||
* Open you .brd file | * Open you .brd file | ||
* Go to Layers Menu | * Go to Layers Menu | ||
* Disable ALL layers but Layer 31 (tCream) | |||
** Doubleclick on Layer 31 (tCream) | ** Doubleclick on Layer 31 (tCream) | ||
** Change Fillstyle to empty | ** Change Fillstyle to empty | ||
| Zeile 48: | Zeile 49: | ||
== Ze actual cutting == | == Ze actual cutting == | ||
Use Overheadfoil that can be used with a copier (than its not PVC) i got splendid results using [http://www.amazon.co.uk/NOBO-Transparency-Plain-Copier-sheets/dp/B000WL1WQI | Use Overheadfoil that can be used with a copier (than its not PVC) i got splendid results using [http://www.amazon.co.uk/NOBO-Transparency-Plain-Copier-sheets/dp/B000WL1WQI OHP Transparency film from NOBO] | ||
You find this in my box in the WEL shelfes on the very right, next to the whiteboard. USe freely for stencils (but nothing else) | You find this in my box in the WEL shelfes on the very right, next to the whiteboard. USe freely for stencils (but nothing else) | ||
| Zeile 64: | Zeile 65: | ||
* Speed: 100 % | * Speed: 100 % | ||
* Power: 10 % | * Power: 10 % | ||
* Hertz: | * Hertz: Vollgas. | ||
[[Kategorie:Howto]] | [[Kategorie:Howto]] | ||
Version vom 17. Juni 2013, 14:07 Uhr
| Language: | English |
|---|
| SMD-Stencils selber machen | |
| |
| Gestartet: | 01.01.2013 |
| Involvierte: | User:Overflo |
| Status: | active |
| Beschreibung: | Howto make SMD stencils |
| Shutdownprozedur: | |
| Zuletzt aktualisiert: | 2013-06-17 |
This page contains Information on how to make a STENCIL for SMD paste
This Information is valid for all the electronic CAD programs but I will document how to do it in eagle.
- Open Eagle
- Open you .brd file
- Go to Layers Menu
- Disable ALL layers but Layer 31 (tCream)
- Doubleclick on Layer 31 (tCream)
- Change Fillstyle to empty
- Scale factor: 1
- Menu ->
- Tools ->
- DRC ->
- Masks ->
- For the CREAM insert MIN: 0 Percent: 90% Max: 4mil
- Masks ->
- DRC ->
- Tools ->
- Click Apply
Now your tCream (31) Layer contains squares/masks that are smaller than the actual pads. GOOD.
We will export this one layer as PDF now.
- Print to file (PDF)
Import the .pdf into Corel draw and you are good to go.
Ze actual cutting
Use Overheadfoil that can be used with a copier (than its not PVC) i got splendid results using OHP Transparency film from NOBO
You find this in my box in the WEL shelfes on the very right, next to the whiteboard. USe freely for stencils (but nothing else)
Place the overheadfoil on a piece of plain white copier paper and cut the stencil with an outline around the PCB
Once you cut it you can remove the overheadfoil from the paper and all the little squers will stick to the paper.
Cutter settings
- Speed: 100 %
- Power: 10 %
- Hertz: Vollgas.
