HSC2011/Enclosure: Unterschied zwischen den Versionen
aus Metalab Wiki, dem offenen Zentrum für meta-disziplinäre Magier und technisch-kreative Enthusiasten.
Zur Navigation springenZur Suche springen
KKeine Bearbeitungszusammenfassung |
Mazzo (Diskussion | Beiträge) |
||
| (6 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
<small>< [[HSC2011]]</small> | |||
__TOC__ | |||
== About the enclosure == | |||
The enclosure was designed and manufactured by [[Benutzer:Mazzo| mazzo]] using Blender and our makerbot "le giraffe" | |||
== Files needed for the production of the enclosure == | |||
* All up to date files are found in the [https://github.com/Metalab/hsc2011/enclosure/ GIT repository] here is short summary of the important files | |||
** [[:Datei:Edubuzzer_stl_gcode.zip | Gcode and STL files]] to feed your 3D printer omnomnomnom | |||
** [[:Datei:edubuzzer_middlepart.cdr | The middlepart for the lazzor]] You should cut this from 6mm acryl | |||
** [[:Datei:EduBuZZer_Final.blend | Blender file ]] | |||
== Some screenshots from Blender == | |||
{| | |||
! width="450"| | |||
! width="450"| | |||
|- | |||
| valign="top"|[[Bild:eb_bottom.png|thumb|400px|left|The bottom of the EduBuzzer enclosure]] | |||
| valign="top"|[[Bild:eb_top.png|thumb|400px|left|The top of the EduBuzzer enclosure]] | |||
|- | |||
| valign="top"|[[Bild:eb_complete_black.png|thumb|400px|left|The complete EduBuzzer enclosure]] | |||
| valign="top"|[[Bild:eb_complete.png|thumb|400px|left|Highlighted Battery holder, on/off switch holder and PCB]] | |||
|} | |||
== Photos of the final enclosure == | |||
{| | |||
! width="450"| | |||
! width="450"| | |||
|- | |||
| valign="top"|[[Bild:Enclosure_and_pcb.JPG|thumb|400px|left|The enclosure + PCB]] | |||
| valign="top"|[[Bild:Enclosure_bottom.JPG|thumb|400px|left|The bottom half of the enclosure]] | |||
|- | |||
| valign="top"|[[Bild:Enclosure_full_assembled.JPG|thumb|400px|left|Fully assembled!]] | |||
| valign="top"|[[Bild:Enclosure_middlepart.JPG|thumb|400px|left|The middlepart is lazzored and the RGB led shines in there to change the color of the enclosure]] | |||
|- | |||
| valign="top"|[[Bild:Enclosure_middlepart_assy.JPG|thumb|400px|left|middlepart attched to the enclosure]] | |||
| valign="top"|[[Bild:Enclosure_pcb_off.JPG|thumb|400px|left|connection on the bottom for the iButton, on/off switch + power]] | |||
|- | |||
| valign="top"|[[Bild:Enclosure_rgb_inlay.JPG|thumb|400px|left|bottompart + middlepart + pcb ]] | |||
|} | |||
==Blender Animation of the enclosure== | |||
{{#ev:youtube|i9sB169s1X8}} | |||
[[Kategorie:HSC2011]] | [[Kategorie:HSC2011]] | ||
[[Kategorie:English]] | [[Kategorie:English]] | ||
Aktuelle Version vom 4. Mai 2011, 04:47 Uhr
< HSC2011
About the enclosure
The enclosure was designed and manufactured by mazzo using Blender and our makerbot "le giraffe"
Files needed for the production of the enclosure
- All up to date files are found in the GIT repository here is short summary of the important files
- Gcode and STL files to feed your 3D printer omnomnomnom
- The middlepart for the lazzor You should cut this from 6mm acryl
- Blender file
Some screenshots from Blender
Photos of the final enclosure
Blender Animation of the enclosure
{{#ev:youtube|i9sB169s1X8}}
